Frymaster H52 Series M-100B Computer Problem Condition Indicators, Recovery Out of Range REC Lock

Page 18

Example 1: In a full-vat fryer, press cook switch 1 when the first basket of twin baskets of fries is dropped. Halfway through the first cooking cycle, drop the second basket and press cook switch 2 .

Example 2: The M-100B is programmed to cook Crispy Chicken (CSPY) and Chicken McNuggets (NUG) in the same side of a split-vat arrangement. Cook switch 1 corresponds to Crispy Chicken, and cook switch 2 corresponds to Chicken McNuggets.

2.The display will show the number of minutes and seconds of cooking time remaining.

3.At the programmed shake time, an audible alarm will sound and the display will flash SHAKE. After shaking the basket, press the corresponding cook switch, 1 or 2 , to cancel the alarm.

4.After the completing the cooking time, an audible alarm will sound and the display will flash pull. Remove the indicated basket and press the corresponding cook switch, 1 or 2 , to cancel the alarm. If no other products are being cooked in the frypot, the display shows 7:00 QA indicating that the quality timer is counting down. If the quality time is set for some time other than 7:00 minutes, the display starts counting down from that time. (QA is not available for McChicken, Crispy Chicken or Filet-o-Fish).

5.When the quality time expires, an audible alarm will sound, and the display will flash QA. Cancel the alarm by pressing the corresponding cook switch, 1 or 2 .

NOTE: When you initiate a new cook cycle, the quality time will automatically reset.

3.5M-100B™ Computer Problem Condition Indicators

Recovery Out of Range (REC LOCK)

Recovery time is an indication of the condition of the fryer. When the fryer is first turned on, the computer records the amount of time it takes to heat the cooking oil from 270°F (132°C) to 320°F (160°C). Also, anytime the temperature of the oil drops below 250°F (121°C), such as when cold oil is added, the computer will check the recovery time. If the fryer takes longer than 2 minutes and 35 seconds to recover, the display will show REC LOCK and the computer will lock out.

To clear the REC LOCK condition, enter the program mode (see How to Enter the Program Mode on Page 3-10) and push the temperature check switch (see diagram on following page).

It is easy to view the currently recorded recovery time with the computer ON. Press the recovery recall switch for the frypot you wish to check. On full-vat units, press the right switch.

If REC LOCK occurs three or more times within a week, verify that oil is not being added while the

fryer is heating (that is, while a heat mode indicator is illuminated) and that the fryer’s power cord is fully plugged in. If oil is not being added while the fryer is heating, and the power cord is fully plugged in, have the fryer checked by a qualified service agent.

3–5

Page 17 Page 19
Image 18
Page 17 Page 19
Contents OPERATOR’S Manual Frymaster H52 Series GAS Fryer Page Introduction GeneralComputer Information European Community CE Specific InformationWhat to do if your equipment arrives damaged Service Information Installation Instructions General Installation RequirementsNational Code Requirements Caster/Leg Installation Non-CE Standard For Incoming Gas Pressures Connection to Gas Line Countries Categories GASCE Standard Converting to Another Gas Type Gas VatNon-CE Gas Conversion Kits CE Gas Conversion Kits for Units with Gas ValveFrypot Boil-Out Operating Fryers With M100B Cooking Computers ShutdownIntroduction To The M-100B Cooking Computer DescriptionOperating the Computer on Full-Vat Fryers Viewing the Frypot Temperature Actual or Setpoint Operating the Computer on Split-Vat FryersCooking Product Full-Vat or Split-Vat M-100B Computer Problem Condition Indicators Recovery Out of Range REC LockOpen Drain Valve Indication Probe Failure Indication M-100B Computer Set-Up and Programming InstructionsHow to Change the Computer’s Display Language 1 M-100B Computer Setup ModeHow to Enter the Setup Mode How to Configure the Computer for Use on a Gas FryerHow to Change Computer Product/Temperature Displays How to Enter the Program Mode How to Activate or Deactivate the Frypot BOIL-OUT Feature2 M-100B Computer Programming Mode How to Reset the Computer to the Factory DefaultsHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test Menu How to Suppress a Shake, QA, or Duty Function How to Display Use Time Information How to Display the Product Cycle Accumulator InformationHow to Use the Filter Countdown Timer Operating Fryers With Analog Controllers Introduction to the Analog ControllerC D E F G H I J K L M N Analog Controller High-Limit Check Page Filtering Operating the Built-In Filtration System Page Operating the Filter Unit Page Getting the Most Out of Your Filter Page Preventive Maintenance and Troubleshooting Preventive MaintenanceTroubleshooting Troubleshooting Fryers with M100B Computers REC LockIgnition Failure Display Remains Blank When ON/OFF Switches are Pressed Troubleshooting Fryers Equipped with Analog Controllers Did burners Troubleshooting Built-in Filtration System Pump does Not RUN
Top Page Image Contents