Frymaster H52 Series warranty How to Activate or Deactivate the Frypot BOIL-OUT Feature

Page 23

For the right side of a split-vat or for a full-vat:Press the right 1 switch to go UP a degree (maximum of 5 for Fahrenheit or 3 for Celsius). Press the right 2 switch to go DOWN a degree (maximum of 5 for Fahrenheit or 3 for Celsius).

5.Press the switch to save the settings.

6.Press either ON/OFF switch to exit the setup mode. Both displays will change to OFF.

How to Activate or Deactivate the Frypot BOIL-OUT Feature

1.Enter the setup mode. See How to Enter the Setup Mode on Page 3-8.

2.Press and release the switch until BOIL-OUTappears in the display.

3.Press the right 1 or 2 switch to toggle the boil-out mode ON or OFF.

4.Press the switch to save the settings.

5.Press either ON/OFF switch to exit the setup mode. Both displays will change to OFF.

3.6.2 M-100B™ Computer Programming Mode

How to Enter the Program Mode

1.Press the ON/OFF switches until both displays of cooking computer indicate OFF. Press the left product selection switch and the left 1 and 2 cook switches simultaneously. Release all three switches at the same time.

2.When the program mode has been entered, the display will flash M-100B computer briefly, followed by the software version number. After a few seconds, Fr fries yes or Fr fries no will be displayed, depending upon previous program settings.

How to Reset the Computer to the Factory Defaults

While in the program mode, press all 4 cook switches (left and right 1 and 2 ) simultaneously to reset the computer to the factory defaults. See How to Enter the Program Mode above. Updating menu will flash in the display, followed by epra cleared and cooks cleared. After a few seconds, Fr fries yes will be displayed, indicating that the computer has been reset to the factory defaults.

How to Change the Shake, Pull, Or Quality Times for Menu Items

1.Enter the program mode. (See How to Enter the Program Mode above.)

2.Press and release the switch until the product to be changed appears in the left display.

3–10

Page 22 Page 24
Image 23
Page 22 Page 24
Contents OPERATOR’S Manual Frymaster H52 Series GAS Fryer Page General IntroductionWhat to do if your equipment arrives damaged Computer InformationEuropean Community CE Specific Information Service Information General Installation Requirements Installation InstructionsNational Code Requirements Caster/Leg Installation Non-CE Standard For Incoming Gas Pressures Countries Categories GAS Connection to Gas LineCE Standard Gas Vat Converting to Another Gas TypeFrypot Boil-Out Non-CE Gas Conversion KitsCE Gas Conversion Kits for Units with Gas Valve Shutdown Operating Fryers With M100B Cooking ComputersDescription Introduction To The M-100B Cooking ComputerOperating the Computer on Full-Vat Fryers Cooking Product Full-Vat or Split-Vat Viewing the Frypot Temperature Actual or SetpointOperating the Computer on Split-Vat Fryers Recovery Out of Range REC Lock M-100B Computer Problem Condition IndicatorsOpen Drain Valve Indication M-100B Computer Set-Up and Programming Instructions Probe Failure IndicationHow to Configure the Computer for Use on a Gas Fryer 1 M-100B Computer Setup ModeHow to Enter the Setup Mode How to Change the Computer’s Display LanguageHow to Change Computer Product/Temperature Displays How to Reset the Computer to the Factory Defaults How to Activate or Deactivate the Frypot BOIL-OUT Feature2 M-100B Computer Programming Mode How to Enter the Program ModeHow to Change the Cooking Temperature Setpoint How to Enter a Product Name in a Test Menu How to Suppress a Shake, QA, or Duty Function How to Display the Product Cycle Accumulator Information How to Display Use Time InformationHow to Use the Filter Countdown Timer Introduction to the Analog Controller Operating Fryers With Analog ControllersC D E F G H I J K L M N Analog Controller High-Limit Check Page Filtering Operating the Built-In Filtration System Page Operating the Filter Unit Page Getting the Most Out of Your Filter Page Troubleshooting Preventive Maintenance and TroubleshootingPreventive Maintenance REC Lock Troubleshooting Fryers with M100B ComputersIgnition Failure Display Remains Blank When ON/OFF Switches are Pressed Troubleshooting Fryers Equipped with Analog Controllers Did burners Troubleshooting Built-in Filtration System Pump does Not RUN
Top Page Image Contents