GE Monogram ZISW42D, ZIS42N, ZISB42D To insert decorative grille panel into the frame

Page 20

Step 9

Connect

power

Installation

42" Built-In Refrigerator

•Connect refrigerator power cord plug to properly grounded receptacle, accessible through the top right side of the grille opening.

•Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on.

PRODUCT

INSTALLATION

Step 10

Mount

Top Grille

Panel

If you are using 3/4" thick custom panels, SKIP THIS STEP. See Custom Panel Dimensions for grille panel sizes. Order ZKT42 kit and follow the installation instructions packed with the kit.

The grille panel frame is factory assembled for an 84" installation height. If installation height varies, order ZG2 trim kit which provides optional side trim pieces.

Cut 1/4" thick custom panel to fit the frame, 41" wide, 9" deep.

To insert decorative grille panel into the frame:

•Remove screws (2 on each top corner) and “L” brackets on each side.

•Slide panel into the frame and reassemble.

•Mount the grille panel by dropping into slots on the case trim.

•For shipping purposes, the top case trim is secured at

84" installation height and must be adjusted.

To raise or lower case trim to other installation heights:

•Loosen 2 screws on both sides and raise the top case trim to meet soffit height or to the top of adjacent cabinets.

•Tighten all 4 screws.

If installation height is more or less than 84", order ZG2 optional grille panel kit which accommodates 83",

83-1/2" and 84-1/2" heights. See installation instructions page 26.

Screws

Top Case Trim

Raise To

Installation

Height

1-1/2" min. gap

Important: Maintain 1-1/2" min. gap between top of doors and bottom of panel frame.

Step 11

Install

Toekick

•A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws.

•A custom toekick can be installed to match or complement the surrounding cabinetry.

–If a custom toekick is to be installed, use the supplied toekick as a template to cut out notches around hinges and waterline tubing.

•For 1/2" to 3/4" thick custom toekicks, additional material should be removed and cut away. This will allow the water and electrical umbilical tube to rotate smoothly when the door is fully opened.

Standard Toekick (Packed with Product)

3-1/4"			1/4" Thick Custom Toekick
3-1/4"

1/2" to 3/4" Thick Custom Toekick Remove Additional Material

4-1/16"

20

Image 20

Contents GE Monogram Built-In Refrigerators ModelsCustom Panel Dimensions Consulter « Mise à terre du réfrigérateur »,Design Information Trim KitsTrue Flush Installation To accomplish an attractive installation, you mustDesign Information Built-In RefrigeratorBuilt-In Refrigerators Thick41-1/2 CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Using Trim Kit ZKT42 Thick panel with standard handle ZKT42 trim kit provides for the installation of 3/4Custom door and grille panels, using the standard full 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserLength handle. Cut panels to size and install Lower freezer panel to allow placement of supportDispenser Brackets and install see detail a Grille Panel height can vary to fill installation67 15/16 Detail a and install Detail B Freezer Rout panels to specification below onSee detail B Standard Custom Detail BFor All Monogram Built-In Refrigerators 23 9/1624 3/4 TrimUse of Extension Cords InstallationUse of Adapter plug Slide carton off top of cabinet Shut off the main water supplyFloor Copper Tubing WasherSide panels must be installed plumb For Installations With a Reverse Osmosis System OnlyStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugTo install 1/4 door panels Step Install Door PanelsStep Roll Refrigerator Into Opening Step Level RefrigeratorRefrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights Parts List ZKH1 Trim Kit For 1/4 PanelsSupport for Custom Handles Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleOption 2 Installation Step Custom handle AssembledDispenser Trim WithTo change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Models TrimDimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel Dimension a Dimension B Install panel support bracketsZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesZKHT1 Trim Kit For 3/4 Panels Fresh food door extrusionFreezer door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesStep Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw Option 1 Installation Model usingFor dispenser BeforeAssembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle Reinstall original screws into the door extrusion Tape extrusions to panels to prevent movementSee a For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 ZWCD1 Trim Kit Custom Dispenser CollarCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram