GE Monogram ZISB42D, ZIS42N, ZISW42D Option 1 Installation Step, Locate position

Page 22

ZKH1 Trim Kit (For 1/4" Panels)

Support for Custom Handles

Option 1 Installation

Step 2

Door Extrusion

Locate position

of handles

 

INSTALLATION

ZKH1

3/4" Min.

1-1/2" Max.

Note: Handle must be located 3/4" to 1-1/2" from edge of extrusion.

•Slide custom panels into fresh food and freezer door frames.

•Temporarily secure the new door extrusions to the doors. Use at least 2 screws on each door.

•The handles must be located 3/4" to 1-1/2" from the edge of the extrusion.

•Determine the desired location of the custom handles and carefully mark centerlines of the screw holes.

•Again, with both doors closed, check the location of the centerlines to be sure they are parallel to the edge of the door, and level with opposite door.

•Drill 1/16" pilot hole through the panel until it starts into the aluminum extrusion. This will mark the matching location for drilling the clearance hole when assem- bling the handle, panel and extrusion.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents GE Monogram Built-In Refrigerators ModelsDesign Information Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Trim KitsDesign Information True Flush InstallationTo accomplish an attractive installation, you must Built-In Refrigerator41-1/2 Built-In RefrigeratorsThick CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Custom door and grille panels, using the standard full Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserDispenser Brackets and install see detail a Length handle. Cut panels to size and installLower freezer panel to allow placement of support Grille Panel height can vary to fill installationSee detail B Standard Custom 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on Detail B24 3/4 For All Monogram Built-In Refrigerators23 9/16 TrimUse of Adapter plug InstallationUse of Extension Cords Floor Copper Tubing Slide carton off top of cabinetShut off the main water supply WasherStep Install Side Panels Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Rotate Clockwise To Remove Filter Bypass PlugStep Roll Refrigerator Into Opening To install 1/4 door panelsStep Install Door Panels Step Level RefrigeratorBlock Top View Refrigerator Cabinet Open freezer door to access case trimRefrigerator Door Spacer Block To raise or lower case trim to other installation heights Installation height and must be adjustedTo insert decorative grille panel into the frame Support for Custom Handles Parts ListZKH1 Trim Kit For 1/4 Panels Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleDispenser Option 2 Installation Step Custom handleAssembled Trim WithZG2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size Custom Panels ZKT42 Trim KitFreezer Door Top trim Side trim Bottom trim Fresh Food Door Models TrimDimension B Step Install1/16 Grille panel Option 1 Installation Step Adjust Grille panel HeightSecure 3/4 panel to grille panel support ZKT42-6-3/4 Dimension a Dimension BInstall panel support brackets Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesFreezer door extrusion ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesMin 2 Max Screw Option 1 Installation Assemble panel, extrusion HandleStep Mount assembled panels For dispenser Option 1 InstallationModel using BeforeAssembled Tubular Stainless Steel Handles ZKHSS1 for 1/4 PanelsTools and materials required Step Match Handle Extrusions to Handle Extrusion Decorator Door PanelSee a for Stainless Steel panels See a Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 Collar trim ZWCD1 Trim KitCustom Dispenser Collar 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram
Top Page Image Contents