GE Monogram ZISW42D, ZIS42N Step Install Standoffs onto Handles, Step Install Assembled Panels

Page 44

ZKHTSS1 for 3/4" panels

Tubular Stainless Steel Handles

Step 3:

Install Standoffs onto Handles

Step 4:

Install

Handles

•Place a handle standoff on each attachment post along the handle. Position the screw hole on the standoff to point to the floor.

•Install set screws into the bottom of each standoff, using the Allen wrench provided. The standoff should be tight against the handle.

•Start mounting screws through the extrusion and just through the custom panel.

•Stand panels up on the hinge side and hold to access the appearance side. Place handle against mounting screws on the appearance side, drive top screw from the back of the extrusion partially into the standoff.

•Going down the handle, drive each screw partially into the standoff, alternating back to the top until the handle is tight against the door.

•Remove tape.

Screw

Allen Wrench

Screw

Step 5:

Install

Assembled

Panels

ZKHTSS1

INSTALLATION

It is best that 2 people perform this step.

•Place panel/handle assembly onto the bottom trim with support bracket tabs inserted into slots.

•Push and hold the panel back against the steel door with door handle extrusion flush to the handle side of the door.

•Reinstall original screws into the door extrusion.

•Open the door fully to stop.

•Install screws at the top, and hinge side.

•Follow the same procedure on the opposite door.

44

Image 44

Contents GE Monogram Built-In Refrigerators ModelsCustom Panel Dimensions Consulter « Mise à terre du réfrigérateur »,Design Information Trim KitsTrue Flush Installation To accomplish an attractive installation, you mustDesign Information Built-In RefrigeratorBuilt-In Refrigerators Thick41-1/2 CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Using Trim Kit ZKT42 Thick panel with standard handle ZKT42 trim kit provides for the installation of 3/4Custom door and grille panels, using the standard full 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserLength handle. Cut panels to size and install Lower freezer panel to allow placement of supportDispenser Brackets and install see detail a Grille Panel height can vary to fill installation67 15/16 Detail a and install Detail B Freezer Rout panels to specification below onSee detail B Standard Custom Detail BFor All Monogram Built-In Refrigerators 23 9/1624 3/4 TrimUse of Extension Cords InstallationUse of Adapter plug Slide carton off top of cabinet Shut off the main water supplyFloor Copper Tubing WasherSide panels must be installed plumb For Installations With a Reverse Osmosis System OnlyStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugTo install 1/4 door panels Step Install Door PanelsStep Roll Refrigerator Into Opening Step Level RefrigeratorRefrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights Parts List ZKH1 Trim Kit For 1/4 PanelsSupport for Custom Handles Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleOption 2 Installation Step Custom handle AssembledDispenser Trim WithTo change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Models TrimDimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel Dimension a Dimension B Install panel support bracketsZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesZKHT1 Trim Kit For 3/4 Panels Fresh food door extrusionFreezer door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesStep Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw Option 1 Installation Model usingFor dispenser BeforeAssembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle Reinstall original screws into the door extrusion Tape extrusions to panels to prevent movementSee a For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 ZWCD1 Trim Kit Custom Dispenser CollarCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram