GE Monogram ZISW42D, ZIS42N, ZISB42D For Stainless Panels, Raised Panel on 1/4 Thick Backing

Page 41

Step 4A:

Install

Handles

and Panels

FOR

STAINLESS

STEEL

PANELS

ZKHSS1 for 1/4" Panels

Tubular Stainless Steel Handles

Door

Handle

Extrusion

Screw

Spacer

Ring

1/4"	Stainless Panel	Stainless	Handle
	Corrugated	Stainless
	Corrugated

Panel

For Stainless Panels:

•Press foam pads against steel doors to temporarily reduce thickness.

•Crimp top and bottom edges of corrugated.

•Slide corrugated onto doors, leave about

1/4" gap between edge of corrugated and hinge side.

Note: Panels have a protective plastic covering. Peel away just enough to allow panel to slide into trim and to clear handle mounting screws. The plastic covering will keep the panels clean during the installation process.

•Slide panels into the door trim. Leave about 4" of the panel exposed to allow room to install the handle

extrusion.

Be sure to maintain 1/4" gap between corrugated and hinge side trim.

•Place a spacer ring over each of the 4 screw holes on the extrusion. Use tape to hold in place.

•Place extrusion onto back side of panel. Use a pencil to punch hole in tape over spacer rings and align with screw holes.

•Install 4 mounting screws through the extrusion and panel.

•Screw handle to panel, starting at the top. Moving down the handle, drive each screw partially into the standoff, alternating back to the top until the handle is tight against the panel.

•Slide the assembly into the door frame until the extrusion fits firmly against the steel door.

•Reinstall original screws into the door extrusion.

Raised Panel on 1/4" Thick Backing:

A raised panel design secured to a 1/4" thick backing (screwed or glued) can be used with this handle kit.

•Cut the 1/4" thick panels to size.

•Fabricate the raised panel to allow 1-1/4" clearance from the hinge side to avoid striking adjacent cabinetry.

•Allow 5/16" clearance at the top, bottom and handle side edges to allow for the trim flange.

•Total thickness should not exceed 3/4".

•Countertops adjacent to the refrigerator installation should be mitered 45°.

Note: Longer screws, obtained locally, will be required to

	1/4"	Appearance
	1/4"	Panel
	Thick	Panel
	Thick
	Backing

1-1/4" Clearance Hinge Side

Case Trim

5/16"

5/16"

Clearance

Handle Side 5/16"

Extrusion

ZKHSS1 INSTALLATION

accommodate panel thickness. Use stainless steel #10-32x1-1/4" truss Phillips head screws.

Screw

Adhesive Backed Foam

41

Image 41

Contents Models GE Monogram Built-In RefrigeratorsConsulter « Mise à terre du réfrigérateur », Custom Panel DimensionsDesign Information Trim KitsTo accomplish an attractive installation, you must True Flush InstallationDesign Information Built-In RefrigeratorThick Built-In Refrigerators41-1/2 CabinetThick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser ZKT42 trim kit provides for the installation of 3/4 Using Trim Kit ZKT42 Thick panel with standard handleCustom door and grille panels, using the standard full 67 15/16Max Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimLower freezer panel to allow placement of support Length handle. Cut panels to size and installDispenser Brackets and install see detail a Grille Panel height can vary to fill installationDetail B Freezer Rout panels to specification below on 67 15/16 Detail a and installSee detail B Standard Custom Detail B23 9/16 For All Monogram Built-In Refrigerators24 3/4 TrimUse of Extension Cords InstallationUse of Adapter plug Shut off the main water supply Slide carton off top of cabinetFloor Copper Tubing WasherFor Installations With a Reverse Osmosis System Only Side panels must be installed plumbStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugStep Install Door Panels To install 1/4 door panelsStep Roll Refrigerator Into Opening Step Level RefrigeratorRefrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights ZKH1 Trim Kit For 1/4 Panels Parts ListSupport for Custom Handles Tor door panels. Handles not included. The doorLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyAssembled Option 2 Installation Step Custom handleDispenser Trim WithTo change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Trim ModelsDimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel Install panel support brackets Dimension a Dimension BZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Handles Step Install PanelsFresh food door extrusion ZKHT1 Trim Kit For 3/4 PanelsFreezer door extrusion Back SideStep Locate position of handles Step Temporarily Mount Door panelsStep Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw Model using Option 1 InstallationFor dispenser BeforeAssembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle Tape extrusions to panels to prevent movement Reinstall original screws into the door extrusionSee a For StainlessRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 Custom Dispenser Collar ZWCD1 Trim KitCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram