GE Monogram ZIS42N, ZISB42D Option 1 Installation, For dispenser, Model using, Before, You begin

Page 36

ZKHT1 Trim Kit (For 3/4" Panels)

Support for Custom Handles

Option 1 Installation

OPTION 2

1-13/16"

1-13/16"

For dispenser

Note: Optimal final

1/4" Max.

model using

appearance depends on careful

Back Side

Back Side

full-width

routing depth. Do not exceed

trim

1⁄4" routing depth.

Handle Side

Handle Side

Before

Freezer Panel

Fresh Food Panel

you begin

All 3 custom door panels must be routed to accommo- date the door extrusions. Route the panels as illustrated, max. 1/4" deep, 1-13/16" wide, top to bottom on the handle side.

Refer to installation instructions for ZKT42 trim kit, Option 2.

•Follow Step No. 1 to remove standard aluminum trim.

•Follow Step No. 2 and 3 to attach new 3/4" trim pieces and install panel support brackets.

Step 1

Locate position of handle

Note: The custom handle must be installed against the handle bracket. The custom handle cannot exceed 11-3/4" length.

INSTALLATION

ZKHT1

Temporarily Temporarily

Secure Secure

Handle Dispenser

Bracket Trim

With With

Screws Screws

•Position the handle bracket onto the steel door by matching existing screw holes on the door and bracket.

•Re-install dispenser trim, temporarily.

•Determine the desired location of the custom handle and carefully mark centerlines of the screw holes.

•Drill 1⁄16" pilot hole through the trim until it starts

into the handle bracket. This marks the same location onto the bracket.

•Remove dispenser trim and bracket.

36

Image 36

Contents GE Monogram Built-In Refrigerators ModelsCustom Panel Dimensions Consulter « Mise à terre du réfrigérateur »,Design Information Trim KitsTrue Flush Installation To accomplish an attractive installation, you mustDesign Information Built-In RefrigeratorBuilt-In Refrigerators Thick41-1/2 CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Using Trim Kit ZKT42 Thick panel with standard handle ZKT42 trim kit provides for the installation of 3/4Custom door and grille panels, using the standard full 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserLength handle. Cut panels to size and install Lower freezer panel to allow placement of supportDispenser Brackets and install see detail a Grille Panel height can vary to fill installation67 15/16 Detail a and install Detail B Freezer Rout panels to specification below onSee detail B Standard Custom Detail BFor All Monogram Built-In Refrigerators 23 9/1624 3/4 TrimInstallation Use of Adapter plugUse of Extension Cords Slide carton off top of cabinet Shut off the main water supplyFloor Copper Tubing WasherSide panels must be installed plumb For Installations With a Reverse Osmosis System OnlyStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugTo install 1/4 door panels Step Install Door PanelsStep Roll Refrigerator Into Opening Step Level RefrigeratorOpen freezer door to access case trim Block Top View Refrigerator CabinetRefrigerator Door Spacer Block Installation height and must be adjusted To raise or lower case trim to other installation heightsTo insert decorative grille panel into the frame Parts List ZKH1 Trim Kit For 1/4 PanelsSupport for Custom Handles Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleOption 2 Installation Step Custom handle AssembledDispenser Trim WithGrille Panel Frame Adjustment ZG2 Trim KitTo change grille panel size ZKT42 Trim Kit Custom PanelsFreezer Door Top trim Side trim Bottom trim Fresh Food Door Models TrimDimension B Option 1 Installation Step Adjust Grille panel Height Step Install1/16 Grille panelSecure 3/4 panel to grille panel support Dimension a Dimension B Install panel support bracketsZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesZKHT1 Trim Kit For 3/4 Panels Fresh food door extrusionFreezer door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesOption 1 Installation Assemble panel, extrusion Handle Min 2 Max ScrewStep Mount assembled panels Option 1 Installation Model usingFor dispenser BeforeAssembled ZKHSS1 for 1/4 Panels Tubular Stainless Steel HandlesTools and materials required Extrusion Decorator Door Panel Step Match Handle Extrusions to HandleSee a for Stainless Steel panels Reinstall original screws into the door extrusion Tape extrusions to panels to prevent movementSee a For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 ZWCD1 Trim Kit Custom Dispenser CollarCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram