GE Monogram ZIS42N, ZISB42D, ZISW42D Custom Panel Dimensions, Non-dispenser

PANEL

		Custom Panel Dimensions
		42" Built-In Refrigerator
	Front View	ZIS42N
Side View	(not to scale)	(Non-dispenser)
(not to scale)	41" Case Width
24 3/4"	42" Overall Width	Design Information

CUSTOM DIMENSIONS

12 1/4" max

10-3/4" min

84 1/2" max

83" min

72 1/4"

4"

*Finished Width

							Wall View
							(not to Scale)
				7"
						5"
		Locate Grounded
			Electrical outlet		18 3/8"
			Within Solid
84 1/2" max			Area Above				74" From
83-1/4" min							Floor to
Finished							Bottom of
Opening							Electrical Area
				Locate Water
				Supply Within
				the Shaded
				Area Below
	5"				5"		3 1/2"
	3 1/2"

Cutout dimensions, clearances and side panel sizes are determined by the many installation options available. Side panels must be used whenever the sides of the refrigerator will be exposed. Side panels are not required when refrigerator is installed into an enclosure or between pantry and oven cabinets. IMPORTANT–Side panels, 1/2" minimum thickness, are required when using

FRAMELESS CABINETS.

•Field installed custom panels, Lexan® or stainless steel panels are required. The door panels and grille panel sizes vary to accommodate the kit being used.

•A custom toekick can be installed to match or comple- ment the surrounding cabinetry. Use the supplied toekick as a template to cut out notches around hinges and water lines.

Optional Kits:

•ZWBP42: Black Lexan® Panel Kit (no trim kit required).

•ZWWP42: White Lexan® Panel Kit (no trim kit required).

•ZWSP42: Stainless Steel Panel Kit (no trim kit required).

•ZKH1: For installation of a custom handle on 1/4" panels.

•ZKT42: For installation of 3/4" custom panels.

•ZKHT1: For installation of a custom handle on 3/4" panels. (This kit must be used in combination with ZKT42.)

•ZKHSS1: Tubular Stainless Steel handles on 1/4" panels.

•ZKHTSS1: Tubular Stainless Steel handles on 3/4" panels. (This kit must be used in combination with ZKT42.)

•ZG2: 1/4" grille panel frame side pieces for 83", 83-1/2" and 84-1/2" installation heights. Factory set height is 84".

•ZWT1: White toekick (supplied toekick is black). Includes a white toekick to fit 36", 42", 48" side-by-side models and 36" bottom mount and single door models.

Additional Specifications

•A 115 volt 60 Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall.

•Water line can enter opening through the floor or back wall. The water line should be 1/4" O.D. copper tubing between the cold water line and water connection location, long enough to extend to the front of the refrigerator. Installation of an easily accessible shut off valve in the water line is recommended.

Clearances

	If the refrigerator is to be installed in a corner:
*42" Min. for a flush installation into an enclosure.	• A 4" min. clearance between the case trim and
*41-1/2" Min. for a semi-flush installation into an enclosure.	adjacent wall on both sides of the refrigerator will
Note: Additional cutout width may be required when side panels are	assure a 90° door opening and access to all drawers. A
used. Add side panel thickness to the finished cutout to calculate	10" clearance is required on both sides for removal
rough-in width. See installation examples on page 4.
	of pans.

6