GE Monogram ZIS42N, ZISB42D, ZISW42D ZKHTSS1 for 3/4 Panels, Tubulor Stainless Steel Handles

Page 42

ZKHTSS1 for 3/4" Panels

Tubulor Stainless Steel Handles

This kit provides for the installation of Stainless Steel

This kit must be used in combination with ZKT42, ZKT42

custom handles on 3/4" thick decorator door panels.

or ZKT48 trim kit.

The door extrusions allow these custom handles to be

The ZKT trim kits provide the framework to support 3/4"

secured to the door structure, rather than to the

thick panels. This kit provides handle side extrusions

custom panels. This kit contains all the necessary parts

and handles to match that ZKT framework.

for dispenser and non-dispenser models.

Note: It is best that 2 people install this kit.

 

Tools and materials required:

•#2 Phillips screwdriver

•Drill and 1/8", 9/32" bits

•Custom door panels

•Safety glasses

•Center punch

•Masking tape

•Hammer

•Pencil

•1/2" thick 12" x 12" min. piece of plywood to protect floor when drilling

•For stainless steel panels wear gloves to

protect against sharp edges.

Parts List:

A. Fresh food door extrusion B. Freezer door extrusion

C. 2 Stainless tubular handles D. 8 Handle standoffs

E. 10 Screws for mounting handle standoffs

(8 required, 2 extra)

F. 10 Set screws (8 required,

2 extra)

G.3/32" Allen wrench for set screws

A

B

C

F

D

E

G

Before

You

Begin

ZKHTSS1

INSTALLATION

•3/4" custom panels must be routed to accommodate these handle extrusions. Rout the panels as illustrated, 1/4" deep, and 1-13/16" wide, top to bottom on the handle side.

•Follow the instructions in the ZKT trim kit to install support brackets to the bottom of the fresh food and freezer panels. For models with full width dispenser trim, install the support bracket to the bottom of the lower panel only. Do not install a bracket to the top of the lower panel or the bottom of the upper panel as shown in the ZKT trim kit instructions. These brackets are not required for this kit.

1-13/16"

 

1-13/16"

Back Side

1/4" Max.

Back Side

Handle Side

Handle Side

Freezer Panel

 

Fresh Food Panel

Back Side Door Panel

Support Bracket

Hinge

Support Bracket

Side

Bottom Edge

 

Bottom Edge

Freezer Panel

 

Fresh Food Panel

Install bottom support brackets only.

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents GE Monogram Built-In Refrigerators ModelsDesign Information Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Trim KitsDesign Information True Flush InstallationTo accomplish an attractive installation, you must Built-In Refrigerator41-1/2 Built-In RefrigeratorsThick CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Custom door and grille panels, using the standard full Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserDispenser Brackets and install see detail a Length handle. Cut panels to size and installLower freezer panel to allow placement of support Grille Panel height can vary to fill installationSee detail B Standard Custom 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on Detail B24 3/4 For All Monogram Built-In Refrigerators23 9/16 TrimInstallation Use of Adapter plugUse of Extension Cords Floor Copper Tubing Slide carton off top of cabinetShut off the main water supply WasherStep Install Side Panels Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Rotate Clockwise To Remove Filter Bypass PlugStep Roll Refrigerator Into Opening To install 1/4 door panelsStep Install Door Panels Step Level RefrigeratorOpen freezer door to access case trim Block Top View Refrigerator CabinetRefrigerator Door Spacer Block Installation height and must be adjusted To raise or lower case trim to other installation heightsTo insert decorative grille panel into the frame Support for Custom Handles Parts ListZKH1 Trim Kit For 1/4 Panels Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleDispenser Option 2 Installation Step Custom handleAssembled Trim WithGrille Panel Frame Adjustment ZG2 Trim KitTo change grille panel size ZKT42 Trim Kit Custom PanelsFreezer Door Top trim Side trim Bottom trim Fresh Food Door Models TrimDimension B Option 1 Installation Step Adjust Grille panel Height Step Install1/16 Grille panelSecure 3/4 panel to grille panel support ZKT42-6-3/4 Dimension a Dimension BInstall panel support brackets Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesFreezer door extrusion ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesOption 1 Installation Assemble panel, extrusion Handle Min 2 Max ScrewStep Mount assembled panels For dispenser Option 1 InstallationModel using BeforeAssembled ZKHSS1 for 1/4 Panels Tubular Stainless Steel HandlesTools and materials required Extrusion Decorator Door Panel Step Match Handle Extrusions to HandleSee a for Stainless Steel panels See a Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 Collar trim ZWCD1 Trim KitCustom Dispenser Collar 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram
Top Page Image Contents