GE Monogram ZISW42D, ZIS42N, ZISB42D installation instructions Dimension B

Page 29

ZKT42 Trim Kit

3/4" Custom Panels

Option 1 Installation

Step 3
Apply panel	Dimension A
support brackets	Dimension A

Back Side Door Panel

ZKT42–6-3/4"

Hinge

Support Bracket

Sde

Dimension B

ZKT42–7-7/8"

Bottom Edge

A

Freezer Panels

Support Bracket

Bottom Edge

B

Fresh Food Panel

Step 4 Install panels

• Position support bracket on freezer panel,	• Secure support brackets to the bottom of the panels
dimension A, from the hinge side edge.	with #4 screws provided. Align the brackets flush with
• Position support bracket on fresh food panel,	the bottom of the panels, with tabs protruding below.
dimension B, from the hinge side edge.	• Bracket location measured from the hinge side, is the
	same for panels with custom handles or standard
	handles.

INSTALLATION	ZKT42
ZKT42 – Install 17 screws

•Place the 3/4" panel on the bottom trim with support bracket tabs inserted into slots. Push the panel back against the steel door, making sure panel is flush to hinge side trim.

•Carefully drill starter holes in panel using a small drill bit.

•Attach the panel to the top and hinge side by installing

screws from the back of the trim through the wood panel.

•Follow the same procedure to install fresh food door panel.

•Re-install door handles with original screws.

29

Image 29

Contents Models GE Monogram Built-In RefrigeratorsConsulter « Mise à terre du réfrigérateur », Custom Panel DimensionsDesign Information Trim KitsTo accomplish an attractive installation, you must True Flush InstallationDesign Information Built-In RefrigeratorThick Built-In Refrigerators41-1/2 CabinetThick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser ZKT42 trim kit provides for the installation of 3/4 Using Trim Kit ZKT42 Thick panel with standard handleCustom door and grille panels, using the standard full 67 15/16Max Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimLower freezer panel to allow placement of support Length handle. Cut panels to size and installDispenser Brackets and install see detail a Grille Panel height can vary to fill installationDetail B Freezer Rout panels to specification below on 67 15/16 Detail a and installSee detail B Standard Custom Detail B23 9/16 For All Monogram Built-In Refrigerators24 3/4 TrimUse of Extension Cords InstallationUse of Adapter plug Shut off the main water supply Slide carton off top of cabinetFloor Copper Tubing WasherFor Installations With a Reverse Osmosis System Only Side panels must be installed plumbStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugStep Install Door Panels To install 1/4 door panelsStep Roll Refrigerator Into Opening Step Level RefrigeratorRefrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights ZKH1 Trim Kit For 1/4 Panels Parts ListSupport for Custom Handles Tor door panels. Handles not included. The doorLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyAssembled Option 2 Installation Step Custom handleDispenser Trim WithTo change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Trim ModelsDimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel Install panel support brackets Dimension a Dimension BZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Handles Step Install PanelsFresh food door extrusion ZKHT1 Trim Kit For 3/4 PanelsFreezer door extrusion Back SideStep Locate position of handles Step Temporarily Mount Door panelsStep Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw Model using Option 1 InstallationFor dispenser BeforeAssembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle Tape extrusions to panels to prevent movement Reinstall original screws into the door extrusionSee a For StainlessRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 Custom Dispenser Collar ZWCD1 Trim KitCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram