GE Monogram ZIS42N, ZISB42D Design Information, Built-In Refrigerator, True Flush Installation

Page 3

Flush or Semi-Flush Enclosure Installations

Design Information

42" Built-In Refrigerator

Advance Planning

DESIGN INFORMATION

0"

True Flush Installation

In a flush installation, the refrigerator doors will align evenly with the

front face of adjacent cabinet doors. The refrigerator blends into the surrounding cabinetry.

Monogram built-in refrigerators can be installed flush with typical 24-3/4" deep cabinetry.

When installed semi-flush, the case trim will conceal slight gaps around the enclosure. The refrigerator will project forward approximately 3/4" beyond the front face of surrounding cabinetry.

In any installation situation, a wide range of appear- ance options can be accomplished through the use of one or more trim kits. See trim kit descriptions and appearance options on page 5.

3/4"

Semi-Flush Installation These refrigerators can also be installed

semi-flush into an enclosure using the minimum cutout width. The case trim creates a frame around the opening.

Side Panel Requirements:

•Side panels are not required whenever the refrigerator is installed into an enclosure or between pantry and oven cabinets.

•Side panels are required whenever the sides of the refrigerator are exposed.

•Side panel sizes vary depending on the type of installation being made.

To accomplish an attractive installation, you must:

1.Determine the need for side panels.

2.Determine side panel thickness.

3.Order matching side panels from the cabinet manufacturer. Be sure to provide the exact dimensions.

Enclosure

Cutout and

Product

Dimensions

• To achieve a flush fit the finished cutout width must

*Finished Width

be at least 42" wide.

Wall View

• A semi-flush installation requires 41-1/2" min. finished

7"

cutout width.

Electrical

5"

• The electrical and water locations must be located as

Area

shown for either type of installation.

18 3/8"

84 1/2"

max

24 3/4" Total

74" From Floor

83-1/4" min

Depth

to Bottom

Finished

of Electrical

Opening

83" Min

84-1/2" Max

5"

Water Supply

5"

3 1/2"

3 1/2"

42"

*42" Min. for a flush installation

24-3/4"

41-1/2" Min. for a semi-flush installation

Note: Additional cutout width may be required when

side panels are used. Add side panel thickness to the

finished cutout to calculate rough-in width. See

installation examples on the following page.

3

Image 3

Contents Models GE Monogram Built-In RefrigeratorsTrim Kits Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Design InformationBuilt-In Refrigerator True Flush InstallationTo accomplish an attractive installation, you must Design InformationCabinet Built-In RefrigeratorsThick 41-1/2Thick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser 67 15/16 Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 Custom door and grille panels, using the standard fullMax Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimGrille Panel height can vary to fill installation Length handle. Cut panels to size and installLower freezer panel to allow placement of support Dispenser Brackets and install see detail aDetail B 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on See detail B Standard CustomTrim For All Monogram Built-In Refrigerators23 9/16 24 3/4Installation Use of Adapter plugUse of Extension Cords Washer Slide carton off top of cabinetShut off the main water supply Floor Copper TubingRotate Clockwise To Remove Filter Bypass Plug Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Step Install Side PanelsStep Level Refrigerator To install 1/4 door panelsStep Install Door Panels Step Roll Refrigerator Into OpeningOpen freezer door to access case trim Block Top View Refrigerator CabinetRefrigerator Door Spacer Block Installation height and must be adjusted To raise or lower case trim to other installation heightsTo insert decorative grille panel into the frame Tor door panels. Handles not included. The door Parts ListZKH1 Trim Kit For 1/4 Panels Support for Custom HandlesLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyTrim With Option 2 Installation Step Custom handleAssembled DispenserGrille Panel Frame Adjustment ZG2 Trim KitTo change grille panel size ZKT42 Trim Kit Custom PanelsFreezer Door Top trim Side trim Bottom trim Fresh Food Door Trim ModelsDimension B Option 1 Installation Step Adjust Grille panel Height Step Install1/16 Grille panelSecure 3/4 panel to grille panel support Back Side Freezer Panels Hinge Upper Lower Dimension a Dimension BInstall panel support brackets ZKT42-6-3/4Step Install Handles Step Install PanelsBack Side ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Freezer door extrusionStep Locate position of handles Step Temporarily Mount Door panelsOption 1 Installation Assemble panel, extrusion Handle Min 2 Max ScrewStep Mount assembled panels Before Option 1 InstallationModel using For dispenserAssembled ZKHSS1 for 1/4 Panels Tubular Stainless Steel HandlesTools and materials required Extrusion Decorator Door Panel Step Match Handle Extrusions to HandleSee a for Stainless Steel panels For Stainless Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement See aRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16 ZWCD1 Trim KitCustom Dispenser Collar Collar trimSelect the door panel size for your application Monogram