GE Monogram ZISB42D, ZIS42N Dimension a Dimension B, ZKT42-6-3/4, Install panel support brackets

Page 31

OPTION 2 For dispenser model using full-width trim

Step 1

Remove handles & trim

Step 2

Install 3/4" trim

ZKT42 Trim Kit

3/4" Custom Panels

• Open freezer door to 90°.

• Remove the Phillips head screws from the full-length handles.

• Open door fully to stop.

• Remove screws from the aluminum trim, top, bottom and hinge side.

• Remove the trim above and below the dispenser.

• Retain screws and full-length handles. Discard original trim.

• Attach the new 3/4" trim pieces at the top and hinge side using original screws.

ZKT42

INSTALLATION

Step 3 Install panel support brackets

Position and mark the location for the support brackets on the back side of the panels. Align all brackets flush with the end of the panels, with tabs protruding over the edge.

On the bottom of the upper panel, measure dimension A from the hinge side.

On the bottom of the lower panel, measure dimension B from the hinge side.

On the top of the lower panel, measure dimension C from the hinge side.

Secure all brackets with #4 screws provided.

Dimension A

Dimension B

Dimension C

ZKT42–4-3/8"

ZKT42–6-3/4"

ZKT42–4-3/8"

C

Back Side

of Freezer

Panels

Hinge

Side

Upper

Panel

Lower

A Panel

B

31

Image 31
Contents Models GE Monogram Built-In RefrigeratorsTrim Kits Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Design InformationBuilt-In Refrigerator True Flush InstallationTo accomplish an attractive installation, you must Design InformationCabinet Built-In RefrigeratorsThick 41-1/2Thick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser 67 15/16 Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 Custom door and grille panels, using the standard fullMax Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimGrille Panel height can vary to fill installation Length handle. Cut panels to size and installLower freezer panel to allow placement of support Dispenser Brackets and install see detail aDetail B 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on See detail B Standard CustomTrim For All Monogram Built-In Refrigerators23 9/16 24 3/4Use of Adapter plug InstallationUse of Extension Cords Washer Slide carton off top of cabinetShut off the main water supply Floor Copper TubingRotate Clockwise To Remove Filter Bypass Plug Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Step Install Side PanelsStep Level Refrigerator To install 1/4 door panelsStep Install Door Panels Step Roll Refrigerator Into OpeningBlock Top View Refrigerator Cabinet Open freezer door to access case trimRefrigerator Door Spacer Block To raise or lower case trim to other installation heights Installation height and must be adjustedTo insert decorative grille panel into the frame Tor door panels. Handles not included. The door Parts ListZKH1 Trim Kit For 1/4 Panels Support for Custom HandlesLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyTrim With Option 2 Installation Step Custom handleAssembled DispenserZG2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size Custom Panels ZKT42 Trim KitFreezer Door Top trim Side trim Bottom trim Fresh Food Door Trim ModelsDimension B Step Install1/16 Grille panel Option 1 Installation Step Adjust Grille panel HeightSecure 3/4 panel to grille panel support Back Side Freezer Panels Hinge Upper Lower Dimension a Dimension BInstall panel support brackets ZKT42-6-3/4Step Install Handles Step Install PanelsBack Side ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Freezer door extrusionStep Locate position of handles Step Temporarily Mount Door panelsMin 2 Max Screw Option 1 Installation Assemble panel, extrusion HandleStep Mount assembled panels Before Option 1 InstallationModel using For dispenserAssembled Tubular Stainless Steel Handles ZKHSS1 for 1/4 PanelsTools and materials required Step Match Handle Extrusions to Handle Extrusion Decorator Door PanelSee a for Stainless Steel panels For Stainless Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement See aRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16 ZWCD1 Trim KitCustom Dispenser Collar Collar trimSelect the door panel size for your application Monogram