GE Monogram ZISW42D ZG2 Trim Kit, Grille Panel Frame Adjustment, To change grille panel size

Page 26

ZG2 Trim Kit

Grille Panel Frame Adjustment

ZG2 INSTALLATION

FOR 83", 83-1/2"

AND 84-1/2"

INSTALLATION

HEIGHTS

•This kit provides optional side trim pieces for the original grille frame to fit 83", 83-1/2" or 84-1/2" installation heights.

To change grille panel size:

•Determine the installation height by measuring the enclosure from the floor to the underside of soffit. When there is no soffit, measure to the top of adjacent cabinets.

•Adjust refrigerator case trim to desired height. See Product Installation.

•Select the side trim pieces for your installation height.

Installation	Panel	Side Trim	Panel
Height	Width	Lengths	Height

83"	41"	8-1/4"	8"
83-1/2"	41"	8-3/4"	8-1/2"
84-1/2"	41"	9-3/4"	9-1/2"

	Barrel	Discard
	Nuts	Discard
	Nuts	Side Trim
		Side Trim
		Pieces

E.Mount the assembled panel by dropping into slots on the case trim.

1-1/2" min. gap

A.Locate original grille panel frame supplied with the refrigerator.

•Remove 8 screws (two on each corner) as illustrated. Discard original side trim pieces.

B. Select correct size of side trim pieces (3 sets provided).

•Secure new side trim pieces to original bottom trim.

Important: Maintain 1-1/2" min. gap between top of doors and bottom of grille panel.

Note: ZG1 Grille Panel Kit is available for models produced before January 1997. Panel sizes for ZG1 and ZG2 are the same. The ZG1 kit can be ordered from your Monogram dealer.

C.Remove barrel nuts from original side trim pieces (2 each side).

•Re-install the barrel nuts on the new side trim pieces you have selected.

D. Slide custom panel into front slots.

•Secure the top trim piece to the frame with “L” brackets and screws.

26

Image 26

Contents GE Monogram Built-In Refrigerators ModelsDesign Information Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Trim KitsDesign Information True Flush InstallationTo accomplish an attractive installation, you must Built-In Refrigerator41-1/2 Built-In RefrigeratorsThick CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Custom door and grille panels, using the standard full Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserDispenser Brackets and install see detail a Length handle. Cut panels to size and installLower freezer panel to allow placement of support Grille Panel height can vary to fill installationSee detail B Standard Custom 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on Detail B24 3/4 For All Monogram Built-In Refrigerators23 9/16 TrimUse of Extension Cords InstallationUse of Adapter plug Floor Copper Tubing Slide carton off top of cabinetShut off the main water supply WasherStep Install Side Panels Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Rotate Clockwise To Remove Filter Bypass PlugStep Roll Refrigerator Into Opening To install 1/4 door panelsStep Install Door Panels Step Level RefrigeratorRefrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights Support for Custom Handles Parts ListZKH1 Trim Kit For 1/4 Panels Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleDispenser Option 2 Installation Step Custom handleAssembled Trim WithTo change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Models TrimDimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel ZKT42-6-3/4 Dimension a Dimension BInstall panel support brackets Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesFreezer door extrusion ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesStep Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw For dispenser Option 1 InstallationModel using BeforeAssembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle See a Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 Collar trim ZWCD1 Trim KitCustom Dispenser Collar 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram