GE Monogram ZISB42D, ZIS42N, ZISW42D installation instructions Assembled

Page 37

ZKHT1 Trim Kit (For 3/4" Panels)

Support for Custom Handles

Option 2 Installation

Step 2

Install

custom handle

Step 3

Mount assembled dispenser trim

•Drill clearance holes through the handle bracket and the dispenser trim.

•Install screw(s) long enough to pass through the

handle bracket, dispenser trim and into the custom handle.

Dispenser Trim

Handle Bracket

Handle Bracket

Dispenser Trim

Custom Handle

•Mount assembled dispenser trim with handle onto the door.

•Drive 2 screws through the top and bottom of the handle bracket into the steel door.

•Re-install 3 screws at top and bottom of dispenser trim.

	Secure	Secure
Important: The handle	Assembled	Handle
bracket must be secured to the	Dispenser	Bracket
steel door. If it is not secured	Trim	With
properly, the dispenser trim will	With	Screws
properly, the dispenser trim will	Screws
pull away from the door.	Screws
pull away from the door.

Again, refer to ZKT42 trim kit, Option 2.

• Follow Step 4 to install freezer door panels and bottom trim.

• Slide freezer handle side extrusion in between panels and steel door. Secure with screws.

•To install fresh food handle, follow the same proce- dure as in Option 1.

Freezer

Handle Side

Extrusion

ZKHT1 INSTALLATION

37

Image 37

Contents Models GE Monogram Built-In RefrigeratorsConsulter « Mise à terre du réfrigérateur », Custom Panel DimensionsDesign Information Trim KitsTo accomplish an attractive installation, you must True Flush InstallationDesign Information Built-In RefrigeratorThick Built-In Refrigerators41-1/2 CabinetThick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser ZKT42 trim kit provides for the installation of 3/4 Using Trim Kit ZKT42 Thick panel with standard handleCustom door and grille panels, using the standard full 67 15/16Max Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimLower freezer panel to allow placement of support Length handle. Cut panels to size and installDispenser Brackets and install see detail a Grille Panel height can vary to fill installationDetail B Freezer Rout panels to specification below on 67 15/16 Detail a and installSee detail B Standard Custom Detail B23 9/16 For All Monogram Built-In Refrigerators24 3/4 TrimUse of Adapter plug InstallationUse of Extension Cords Shut off the main water supply Slide carton off top of cabinetFloor Copper Tubing WasherFor Installations With a Reverse Osmosis System Only Side panels must be installed plumbStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugStep Install Door Panels To install 1/4 door panelsStep Roll Refrigerator Into Opening Step Level RefrigeratorBlock Top View Refrigerator Cabinet Open freezer door to access case trimRefrigerator Door Spacer Block To raise or lower case trim to other installation heights Installation height and must be adjustedTo insert decorative grille panel into the frame ZKH1 Trim Kit For 1/4 Panels Parts ListSupport for Custom Handles Tor door panels. Handles not included. The doorLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyAssembled Option 2 Installation Step Custom handleDispenser Trim WithZG2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size Custom Panels ZKT42 Trim KitFreezer Door Top trim Side trim Bottom trim Fresh Food Door Trim ModelsDimension B Step Install1/16 Grille panel Option 1 Installation Step Adjust Grille panel HeightSecure 3/4 panel to grille panel support Install panel support brackets Dimension a Dimension BZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Handles Step Install PanelsFresh food door extrusion ZKHT1 Trim Kit For 3/4 PanelsFreezer door extrusion Back SideStep Locate position of handles Step Temporarily Mount Door panelsMin 2 Max Screw Option 1 Installation Assemble panel, extrusion HandleStep Mount assembled panels Model using Option 1 InstallationFor dispenser BeforeAssembled Tubular Stainless Steel Handles ZKHSS1 for 1/4 PanelsTools and materials required Step Match Handle Extrusions to Handle Extrusion Decorator Door PanelSee a for Stainless Steel panels Tape extrusions to panels to prevent movement Reinstall original screws into the door extrusionSee a For StainlessRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 Custom Dispenser Collar ZWCD1 Trim KitCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram