GE Monogram ZISB42D, ZIS42N, ZISW42D Built-In Refrigerators, Thick, 41-1/2, Cabinet

Page 4

DESIGN INFORMATION

Design Information

Installation Examples	42" Built-In Refrigerators

Side panels are required whenever the sides of the refrigera-	Therefore, the rough-in dimensions must allow for side panel
tor will be exposed.	thickness. In both a flush and semi-flush installation, the
1/2" to 3/4" side panels are normally set into place and	finished dimension, (the width of the opening after side panels
	are installed), must accommodate the full width of the
fastened to adjacent cabinetry or to the back wall before	refrigerator.
rolling the refrigerator into the opening.
	See page 14 for side panel sizes.

Installation

Between

Base &

Wall Cabinets

Flush and Semi-Flush

	Installations
	1/4" Thick
	Side Panels
Finished Dim.	41-1/2"
Roughed-In Dim.	42"

Note: 1/4" thick side panels can be inserted into the case trim, making the rough-in the same as the outside trim width, 42".

Refrigerator

Cabinet

Refrigerator door

Cabinet

1/4" Side Panels. Insert end of

side panel into trim

Installation At End-of-Run

Flush and Semi-Flush

Installations

1/2" Thick

Side Panels

42" Finished Dim.

43" Rough-In Dim.

Note: 1/2" thick side panels shown. Side panels can be any thickness. Add side panel thickness to outside trim width (42") to calculate the rough-in dimension. The leading (front) edge must be finished to match surrounding cabinetry.

Refrigerator

Cabinet

Refrigerator door

Cabinet

1/2" To 3/4" Side Panels. Leading

Edge Flush With Cabinet

Frameless Cabinets

Side panels, 1/2" minimum thickness are required when using frameless cabinets. The side panel acts as a spacer between the cabinet and the case trim and prevents interference with cabinet door swing. The leading (front) edge must be finished to match surrounding cabinetry.

1/2" To 3/4" Side Panels. Leading

Edge Flush With Cabinet

Refrigerator

Cabinet

Refrigerator door

Accessory Panel Kits

Field installed door and grille panels are required. The factory installed trim will accept accessory panel kits. White or black Lexan® and stainless steel kits are available. Panels are cut to size and ready to install. These panel kits must be ordered separately.

Model	Black	White	Stainless
ZIS42N	ZWBP42	ZWWP42	ZWSP42
ZISW42D		ZWWP42D	ZWSP42D
ZISB42D	ZWBP42D		ZWSP42D

A wide range of custom appearance options can be created with optional custom trim kits. See the opposite page for examples and trim kit descriptions.

4

Image 4

Contents GE Monogram Built-In Refrigerators ModelsCustom Panel Dimensions Consulter « Mise à terre du réfrigérateur »,Design Information Trim KitsTrue Flush Installation To accomplish an attractive installation, you mustDesign Information Built-In RefrigeratorBuilt-In Refrigerators Thick41-1/2 CabinetYou should Thick custom panels-Without trim kitsCustom Panel Dimensions Non-dispenserZIS42N non-dispenser Using Trim Kit ZKT42 Thick panel with standard handle ZKT42 trim kit provides for the installation of 3/4Custom door and grille panels, using the standard full 67 15/16Freezer Panel MaxZISW42D white dispenser ZISB42D black dispenserCustom Door Panel Dimensions Using Standard Trim ZISW42D white dispenser ZISB42D black dispenserLength handle. Cut panels to size and install Lower freezer panel to allow placement of supportDispenser Brackets and install see detail a Grille Panel height can vary to fill installation67 15/16 Detail a and install Detail B Freezer Rout panels to specification below onSee detail B Standard Custom Detail BFor All Monogram Built-In Refrigerators 23 9/1624 3/4 TrimUse of Adapter plug InstallationUse of Extension Cords Slide carton off top of cabinet Shut off the main water supplyFloor Copper Tubing WasherSide panels must be installed plumb For Installations With a Reverse Osmosis System OnlyStep Install Side Panels Rotate Clockwise To Remove Filter Bypass PlugTo install 1/4 door panels Step Install Door PanelsStep Roll Refrigerator Into Opening Step Level RefrigeratorBlock Top View Refrigerator Cabinet Open freezer door to access case trimRefrigerator Door Spacer Block To raise or lower case trim to other installation heights Installation height and must be adjustedTo insert decorative grille panel into the frame Parts List ZKH1 Trim Kit For 1/4 PanelsSupport for Custom Handles Tor door panels. Handles not included. The doorOption 1 Installation Step Locate positionOption 1 Installation Step Assemble panel Extrusion Handle Extrusion Decorator Door Panel Handle Min 2 Max Door HandleRe-install dispenser trim, temporarily Step Locate Position HandleOption 2 Installation Step Custom handle AssembledDispenser Trim WithZG2 Trim Kit Grille Panel Frame AdjustmentTo change grille panel size Custom Panels ZKT42 Trim KitFreezer Door Top trim Side trim Bottom trim Fresh Food Door Models TrimDimension B Step Install1/16 Grille panel Option 1 Installation Step Adjust Grille panel HeightSecure 3/4 panel to grille panel support Dimension a Dimension B Install panel support bracketsZKT42-6-3/4 Back Side Freezer Panels Hinge Upper LowerStep Install Panels Step Install HandlesZKHT1 Trim Kit For 3/4 Panels Fresh food door extrusionFreezer door extrusion Back SideStep Temporarily Mount Door panels Step Locate position of handlesMin 2 Max Screw Option 1 Installation Assemble panel, extrusion HandleStep Mount assembled panels Option 1 Installation Model usingFor dispenser BeforeAssembled Tubular Stainless Steel Handles ZKHSS1 for 1/4 PanelsTools and materials required Step Match Handle Extrusions to Handle Extrusion Decorator Door PanelSee a for Stainless Steel panels Reinstall original screws into the door extrusion Tape extrusions to panels to prevent movementSee a For StainlessFor Stainless Panels Raised Panel on 1/4 Thick BackingZKHTSS1 for 3/4 Panels Tubulor Stainless Steel HandlesFreezer panels Step Install Standoffs onto Handles Step Install Assembled PanelsZKHTSS1 ZWCD1 Trim Kit Custom Dispenser CollarCollar trim 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16Select the door panel size for your application Monogram