GE Monogram ZIS42N Extrusion Decorator Door Panel, Step Match Handle Extrusions to Handle

Page 39

ZKHSS1 for 1/4" Panels

Tubular Stainless Steel Handles

Step 2:

Match

Handle Extrusions to Handle

FOR CUSTOM

WOOD

PANELS

See Step 2A for Stainless Steel panels

•Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood to protect flooring when drilling.

•Place custom panels on the pad, appearance side down.

Note: If panels are wood, be sure to note which end is the top so that wood grain is in the correct direction on both (or all 3) panels.

•On the back side of the panel – at the handle side, measure and mark 1/4" below the top edge of the panel with a pencil.

•Slip panels into new extrusion on the handle side of the panels.

•Align the extrusion at the pencil mark, 1/4" below the top of the panel.

•Follow the same procedure on the opposite panel.

•Tape the extrusions to the panels to prevent move- ment.

•Center punch and drill 1/8" pilot holes through the holes in the extrusion and into the panel.

•Turn panel over. On the appearance side, use 9/32" bit to enlarge clearance hole.

IMPORTANT: Hole locations must be exact to accept handle standoff and handle assembly.

For models with full width dispenser trim and 2 piece freezer panels:

•Measure 1/4" from the top of the upper panel and 1/4" from the bottom of the lower panel. Mark with pencil on the back handle side.

•Align the extrusion on the pencil mark as shown, top and bottom.

Freezer

Upper

Panel

Back

Side

Freezer

Lower

Panel

Models

With Full Width

Dispenser Trim

Top	Note: Be sure to orient
End	extrusions and handles
	correctly. The top ends of the
	extrusions are cutout to fit the
	shape of the top of the door.

	Align Extrusion
	1/4" Below Top
	of Panel
	Back
	Side
	Fresh
	Food
	Panel
Back
Side
Freezer
Panel
Freezer	Fresh Food
Extrusion	Extrusion

ZKHSS1

INSTALLATION

Extrusion

Decorator

Door

Panel

39

Image 39

Contents Models GE Monogram Built-In RefrigeratorsTrim Kits Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Design InformationBuilt-In Refrigerator True Flush InstallationTo accomplish an attractive installation, you must Design InformationCabinet Built-In RefrigeratorsThick 41-1/2Thick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser 67 15/16 Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 Custom door and grille panels, using the standard fullMax Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimGrille Panel height can vary to fill installation Length handle. Cut panels to size and installLower freezer panel to allow placement of support Dispenser Brackets and install see detail aDetail B 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on See detail B Standard CustomTrim For All Monogram Built-In Refrigerators23 9/16 24 3/4Installation Use of Adapter plugUse of Extension Cords Washer Slide carton off top of cabinetShut off the main water supply Floor Copper TubingRotate Clockwise To Remove Filter Bypass Plug Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Step Install Side PanelsStep Level Refrigerator To install 1/4 door panelsStep Install Door Panels Step Roll Refrigerator Into OpeningOpen freezer door to access case trim Block Top View Refrigerator CabinetRefrigerator Door Spacer Block Installation height and must be adjusted To raise or lower case trim to other installation heightsTo insert decorative grille panel into the frame Tor door panels. Handles not included. The door Parts ListZKH1 Trim Kit For 1/4 Panels Support for Custom HandlesLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyTrim With Option 2 Installation Step Custom handleAssembled DispenserGrille Panel Frame Adjustment ZG2 Trim KitTo change grille panel size ZKT42 Trim Kit Custom PanelsFreezer Door Top trim Side trim Bottom trim Fresh Food Door Trim ModelsDimension B Option 1 Installation Step Adjust Grille panel Height Step Install1/16 Grille panelSecure 3/4 panel to grille panel support Back Side Freezer Panels Hinge Upper Lower Dimension a Dimension BInstall panel support brackets ZKT42-6-3/4Step Install Handles Step Install PanelsBack Side ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Freezer door extrusionStep Locate position of handles Step Temporarily Mount Door panelsOption 1 Installation Assemble panel, extrusion Handle Min 2 Max ScrewStep Mount assembled panels Before Option 1 InstallationModel using For dispenserAssembled ZKHSS1 for 1/4 Panels Tubular Stainless Steel HandlesTools and materials required Extrusion Decorator Door Panel Step Match Handle Extrusions to HandleSee a for Stainless Steel panels For Stainless Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement See aRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16 ZWCD1 Trim KitCustom Dispenser Collar Collar trimSelect the door panel size for your application Monogram