GE Monogram ZISW42D Min 2 Max Screw, Option 1 Installation Assemble panel, extrusion Handle

Page 35

ZKHT1 Trim Kit (For 3/4" Panels)

Support for Custom Handles

Option 1 Installation

Step 3 Assemble panel, extrusion

and handle

•Remove the door extrusions and door panels.

•Drill 1/16" pilot hole through extrusion.

•Drill clearance holes through the panel and extrusion.

•Assemble the door panel, extrusions and custom handle.

•Install screw(s) long enough to pass through the extrusion, door panel and into the handle.

3/4" Min.

1-1/2" Max.

Screw

Step 4

Mount assembled panels

•Place assembled panel onto bottom trim with support bracket tabs inserted into slots.

•Push the panel back against the steel door with door extrusion flush to the handle side of the door.

•Open door fully to stop.

• Install screws at the top, hinge side and end of door	Door Handle
• Install screws at the top, hinge side and end of door
extrusion.

ZKHT1 INSTALLATION

Image 35

Contents Models GE Monogram Built-In RefrigeratorsTrim Kits Custom Panel DimensionsConsulter « Mise à terre du réfrigérateur », Design InformationBuilt-In Refrigerator True Flush InstallationTo accomplish an attractive installation, you must Design InformationCabinet Built-In RefrigeratorsThick 41-1/2Thick custom panels-Without trim kits You shouldNon-dispenser Custom Panel DimensionsZIS42N non-dispenser 67 15/16 Using Trim Kit ZKT42 Thick panel with standard handleZKT42 trim kit provides for the installation of 3/4 Custom door and grille panels, using the standard fullMax Freezer PanelZISB42D black dispenser ZISW42D white dispenserZISW42D white dispenser ZISB42D black dispenser Custom Door Panel Dimensions Using Standard TrimGrille Panel height can vary to fill installation Length handle. Cut panels to size and installLower freezer panel to allow placement of support Dispenser Brackets and install see detail aDetail B 67 15/16 Detail a and installDetail B Freezer Rout panels to specification below on See detail B Standard CustomTrim For All Monogram Built-In Refrigerators23 9/16 24 3/4Use of Extension Cords InstallationUse of Adapter plug Washer Slide carton off top of cabinetShut off the main water supply Floor Copper TubingRotate Clockwise To Remove Filter Bypass Plug Side panels must be installed plumbFor Installations With a Reverse Osmosis System Only Step Install Side PanelsStep Level Refrigerator To install 1/4 door panelsStep Install Door Panels Step Roll Refrigerator Into OpeningRefrigerator Door Spacer Block Open freezer door to access case trimBlock Top View Refrigerator Cabinet To insert decorative grille panel into the frame Installation height and must be adjustedTo raise or lower case trim to other installation heights Tor door panels. Handles not included. The door Parts ListZKH1 Trim Kit For 1/4 Panels Support for Custom HandlesLocate position Option 1 Installation StepExtrusion Decorator Door Panel Handle Min 2 Max Door Handle Option 1 Installation Step Assemble panel Extrusion HandleStep Locate Position Handle Re-install dispenser trim, temporarilyTrim With Option 2 Installation Step Custom handleAssembled DispenserTo change grille panel size Grille Panel Frame AdjustmentZG2 Trim Kit Freezer Door Top trim Side trim Bottom trim Fresh Food Door ZKT42 Trim KitCustom Panels Trim ModelsDimension B Secure 3/4 panel to grille panel support Option 1 Installation Step Adjust Grille panel HeightStep Install1/16 Grille panel Back Side Freezer Panels Hinge Upper Lower Dimension a Dimension BInstall panel support brackets ZKT42-6-3/4Step Install Handles Step Install PanelsBack Side ZKHT1 Trim Kit For 3/4 PanelsFresh food door extrusion Freezer door extrusionStep Locate position of handles Step Temporarily Mount Door panelsStep Mount assembled panels Option 1 Installation Assemble panel, extrusion HandleMin 2 Max Screw Before Option 1 InstallationModel using For dispenserAssembled Tools and materials required ZKHSS1 for 1/4 PanelsTubular Stainless Steel Handles See a for Stainless Steel panels Extrusion Decorator Door PanelStep Match Handle Extrusions to Handle For Stainless Reinstall original screws into the door extrusionTape extrusions to panels to prevent movement See aRaised Panel on 1/4 Thick Backing For Stainless PanelsTubulor Stainless Steel Handles ZKHTSS1 for 3/4 PanelsFreezer panels Step Install Assembled Panels Step Install Standoffs onto HandlesZKHTSS1 17 11/16 67 7/8 15 1/4 67 15/16 15 1/16 15 5/16 ZWCD1 Trim KitCustom Dispenser Collar Collar trimSelect the door panel size for your application Monogram