Grd Plm Plf | Goodmans DSZ, GSZ, ASZ, SSX, ASX, DSX, GSX, SSZ

ACCESSORIES WIRING DIAGRAMS

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS

UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

HTR2 TL

HTR1 TL

HTR1

HTR2

HTR1 TL

HTR2

HTR3

HTR4 TL

BK RD

ONE (1) ELEMENT ROWS

TWO (2) ELEMENT ROWS

THREE (3) ELEMENT ROWS

FOUR (4) ELEMENT ROWS

NOTE: WHEN INSTALLING HEATER KIT, ENSURE SPEED TAP DOES NOT EXCEED MINIMUM BLOWER SPEED (MBS) SPECIFIED FOR THE AIRHANDLER/HEAT ER

KIT COMBINATION ON THIS UNIT'S S&R PLATE. AFTER INSTALLING OPTIONAL HEAT KIT, MARK AN "X" IN THE PROVIDED ABOVE. MARK ACCORDING TO NUMBER OF HEATER ELEMENT ROWS INSTALLED. NO MARK INDICATES NO HEAT KIT INSTALLED.

TERMINAL BLOCK SHOWN

EQUIPMENT GROUND

FOR 50HZ MODELS ONLY

USE COPPER OR ALUMINUM WIRE

RD GR WH

GRD

PLM

PLF

SEE

NOTE 4

NOTE

SEE NOTE 5

EBTDR

SEE NOTE 1

240

XFMR-R

COM

XFMR-C

24V

SPEEDUP

COPPER OR ALUMINUM

RD SEE

NOTE

POWER SUPPLY

(SEE RATING PLATE)

USE MIN. 75°C FIELD WIRE

THREE SPEED MOTOR WIRING					RD
(SELECT MODELS ONLY)	(M1) RD		LOW		RD
SEE NOTE 3	(M2)	BL	MEDIUM		RC
	(COM) BK		HIGH		RC
	(COM) BK		HIGH		BR
	(TR 1)	PU			BR
	(TR 1)			EM	EM
			BR	EM	EM
IF REPLACEMENT OF THE ORIGINAL WIRES			BR	3 SPEED	BR
IF REPLACEMENT OF THE ORIGINAL WIRES	PU			3 SPEED	BR
SUPPLIED WITH THIS ASSEMBLY IS NECESSARY,
USE WIRE THAT CONFORMS TO THE		RC
NATIONAL ELECTRIC CODE.

	208/240 VOLTS
L1	L2
1 PLM	PLM 2

	1	PLF				3		PLF	2
						3		PLF	2
		RC		EM
						M1	NC	NO
						M1	NC
						LO		EBTDR
								EBTDR
						M2	COM
						HI	COM
						HI
		1	2	3		SEE NOTE 1
		TR
EBTDR	R	4	24V	5		C	EBTDR		G
		4	24V	5
			6	5	4	PLF
	RD		WH BR			BL			GR

COLOR CODE

WIRING CODE

BLACK

GREEN

FACTORY WIRING

RED

PURPLE

HIGH VOLTAGE

YELLOW

BROWN

LOW VOLTAGE

BLUE

WHITE

FIELD WIRING

HIGH VOLTAGE

COMPONENT CODE

LOW VOLTAGE NOTE 2

EVAPORATOR MOTOR

TRANSFORMER

RUN CAPACITOR

PLF

FEMALE PLUG CONNECTOR

STRAIN RELIEF

PLM

MALE PLUG CONNECTOR

RELAY

FUSE LINK

EBTDR

ELECTRONIC BLOWER TIME

THERMAL LIMIT

Notes:

DELAY RELAY

HTR

HEAT ELEMENTS

1)Red wires to be on transformer terminal "3" for 240 volts and on terminal "2" for 208 volts.

2)See composite wiring diagrams in installation instructions for proper low voltage wiring connections.

3)Confirm speed tap selected is appropriate for application. If speed tap needs to be changed, connect appropriate motor wire (Red for low, Blue for medium, and Black for high speed) on "COM" connection of the EBTDR.

Inactive motor wires should be connected to "M1 or M2" on EBTDR.

4)Brown and white wires are used with Heat Kits only.

5)EBTDR has a 7 second on delay when "G" is energized and a 65 second off

delay when "G" is de-energized.	0140M00037

Typical Wiring Schematic ADPF, ARPF, ARUF with Electric Heat.

This wiring diagram is for reference only. Not all wiring is as shown above.

Refer to the appropriate wiring diagram for the unit being serviced.