AC Power and Control
AC Power Input
Your RCC-1055 is configured at the factory for the proper AC voltage in the country where you purchased it (either 115 volts or 230/240 volts. The AC line configuration is noted on a decal on the back panel.
NOTE: Should you move your CD player to another country, it may be possible to re- configure it for use on a different line volt- age. Do not attempt to perform this conversion yourself. Opening the enclosure of the RCC-1055 exposes you to danger- ous voltages. Consult a qualified service person or the Rotel factory service depart- ment for information.
The RCC-1055 should be plugged directly into
a2-pin polarized wall outlet or into the switched outlet on another component in your audio system. Do not use an extension cord.
Be sure the power switch on the front panel of the RCC-1055 is turned off (in the "out" position). Then plug the power cord into an AC power outlet.
If you are going to be away from home for an extended period of time such as a month- long vacation, it is a sensible precaution to unplug your CD player (as well as other au- dio and video components) while you are away.
Power Switch and Power Indicator
The Power Switch is located on the left side of the front panel. Push the switch button in to turn on the RCC-1055. To turn the RCC-1055 off, push the button again to return it to the "out" position.
NOTE: If you are using a switched outlet to turn on and off your CD player, you should leave the power switch in the "on" position. When AC power is applied to the unit, it will power up in fully active mode.
When the Power Switch is turned on the disc in position 1 in the tray is selected. The Disc and Track Displays illuminate and show Disc 1/ Track 1. The Time Indicator also illuminates.
Output Connections
The RCC-1055 gives you a choice of analog or digital output signals. The analog output signal from the built-in Digital to Analog con- verter is used with conventional analog au- dio components. The digital output, which pro- vides an unprocessed digital data signal, is used with outboard D/A converters or digi- tal processors.
NOTE: To prevent loud noises that neither you nor your speakers will appreciate, make sure all the system components are turned off when you make any signal con- nections.
Analog Outputs
[See Figure 4 for wiring illustration]
A pair of standard RCA jacks supplies a con- ventional unbalanced analog output signal from the RCC-1055 to the source inputs of an audio preamplifier, integrated amplifier, or receiver. RCA connections are found on vir- tually all components. Select high quality au- dio interconnect cables. Connect the left chan- nel output of the RCC-1055 to the left chan- nel source input on the preamplifier or other component. Connect the right output of the RCC-1055 to the right channel source input on the preamplifier or other component.
Digital Output
[See Figure 5 for connection illustra- tion]
If you are using the RCC-1055 as a disc trans- port with an outboard D/A converter or other digital processor, you need an unprocessed digital data stream from the RCC-1055, taken before the built-in D/A converter. This signal is supplied by the back-panel coaxial digital output jack. Using a standard 75 ohm coax cable, connect the digital output jack to the digital input connector on the outboard D/A converter.
Remote Control
The RCC-1055 is supplied with an RR-D92 remote control. When using the RR-D92 the emitter on the front of the control must be pointed at the RCC-1055 front panel. The basic disc play functions are controlled by the but- ton located near the front of the RR-D92. There is a cover over the lower portion of the RR-D92 that slides down to reveal buttons that con- trol secondary functions, such as programming, disc scanning and direct disc selection.
The RR-D92 duplicates the basic disc play control functions of the front panel control but- tons. When a disc play control is on both the front panel and the remote control, both control identifiers are shown in the related instruction text. For example, to play a disc you can press either on the front panel or on the re- mote control. There are some functions, such as programmed track play functions, that are operated exclusively by the RR-D92.
Remote Sensor
The Remote Sensor picks up the infrared sig- nals from the remote control. Do not cover or block the sensor. It must be unobstructed or the remote control will not work properly. The operation of the Remote Sensor can also be affected if it is exposed to bright light, par- ticularly sunlight. Certain types of lighting, such as halogen lights, that emit a fair amount of infrared light, can also interfere with proper operation. In addition remote control functions may not work reliably if the batteries in the RR-D92 are weak.
External Remote Input
This connector is designed to be used in con- junction with Xantechª brand Video Linkª IR signal pick ups (sold separately by custom system installers). This feature enables you to operate the RCC-1055 with the hand held re- mote control even when it is installed where it is not visible from your listening location. Contact your authorized Rotel dealer for more information.
Video Link and Xantech are Trademarks of Xantech Corporation.