Kenmore 665.1602 Quick Rinse, Do not Use detergent With this Cycle, To stop the drain, Sani Rinse

Quick Rinse

Use this rinse cycle for rinsing dishes, glasses, and silverware that will not be washed right away.

_	Do not	use detergent		with this	cycle.
Wash	Main	Rinse	Final	Dry	Time	Water
	Wash	or	Rinse		(rnin)	Usage
		Purge				(gal/L)
		•			10	1.8-2.2/
		Rinse				6.8-8.3

*If the incoming water temperature is less than the recommended temperature or food soils are heavy, the cycle will automatically compensate by adding time, heat and water as needed.

1.Press CANCEL/DRAIN. The Cancel/Drain light glows.

2.The dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely. The light turns off after

2 minutes. The door must be closed for the dishwasher to drain.

To stop the drain

You can press CANCEL!DRAIN again to stop the drain. Remember to drain the dishwasher before starting a new cycle.

To clear the indicators

Press CANCEL!DRAIN before starting the dishwasher to clear all options and cycles.

You can add an item anytime before the main wash starts. Open the door and check the detergent dispenser. If the cover is still closed, you can add items.

To add items

1.Carefully open the door slightly to stop the cycle. Wait for the spraying action to stop before opening the door. The Start/ Resume light will flash.

2.Open the door. If the detergent dispenser cover is still closed, add the item.

3.Close the door firmly until it latches.

4.Press START/RESUME.

IMPORTANT: If Lock On is selected, turn off the lock (see Lock On section in "Option Selections"), or the Start/Resume light will continue to flash.

You can customize your cycles by pressing an option. If you change your mind, press the option again to turn the option off, or select a different option if desired.

You can change an option anytime before the selected option begins. For example, you can press an unheated drying option anytime before drying begins.

Press START/RESUME to use the same cycle and option(s) as the previous wash cycle.

NOTE: If the last cycle you completed was a rinse cycle, when you press START/RESUME, the dishwasher runs the last full wash cycle and options.

During the first minute of a cycle

1.Select a new cycle and/or options.

2.Check the detergent dispensers. They must be filled properly for the new cycle.

3.The Start/Resume light will flash when the door is opened. Make sure the door is closed.

4.Press START/RESUME.

After the first minute of a cycle

1.Press CANCEL!DRAIN. The Cancel/Drain light glows. Your dishwasher starts a 2-minute drain (if needed). Let the dishwasher drain completely.

2.Check the detergent dispensers. They must be filled properly for the new cycle.

3.Make sure the door is closed.

4.Select a new cycle and/or options.

5.Press START/RESUME.

Hi Temp Wash

Select this option to increase the water temperature during the wash portions of the cycle. Hi Temp Wash raises the water temperature to 145°F (63°C), in the main wash. Heating the water helps improve washing results. Hi Temp Wash is useful when loads contain tough food soil.

This option may add heat and wash time to the cycle.

NOTE: Hi Temp Wash is an option with the SMART WASH TM, Pots Pans, and Normal Wash cycles.

Sani Rinse

Select this option to raise the water temperature in the final rinse to approximately 155°F (68°C). Sani Rinse adds heat and time to the cycle. This high temperature rinse sanitizes your dishes and glassware in accordance with NSF/ANSl Standard 184 for Residential Dishwashers. Certified residential dishwashers are not intended for licensed food establishments.

NOTE: Sani Rinse is an option with SMART WASH TM, Pots Pans, and Normal Wash cycles. Only these sanitization cycles have been designed to meet the NSF/ANSI requirements.

14