Husqvarna 953876562 Blade, Guarantee and Guarantee Policy, EC Declaration of Conformity

			BLADE
			To remove the blade (19) unscrew the screw	When reassembling, make sure that the key (22) is cor-
		(20).		rectly seated in the shaft and that the cutting edges face
Check the conditions of the blade-support (21), the key				in the direction of the engine rotation. The blade screw
	(22) and replace any parts which are damaged.			(20) must be torqued to 3,7 Kgm (35 Nm).

Guarantee and Guarantee Policy

If any part is found to be defective due to faulty manufacture within the guarantee period, Husqvarna Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing:

a)The fault is reported directly to the Authorised Re- pairer.

b)Proof of purchase is provided.

c)The fault is not caused by misuse, neglect or faulty adjustment by the user.

d)The failure has not occurred through fair wear and tear.

e)The machine has not been serviced or repaired, taken apart or tampered with by any person not authorised by Husqvarna Outdoor Products.

f)The machine has not been used for hire.

g)The machine is owned by the original purchaser.

h)The machine has not been used commercially.

This guarantee is additional to, and in no way diminishes the customers statutory rights.

Failures due to the following are not covered, therefore it is important that you read the instructions contained in

this Operator’s Manual and understand how to operate and maintain your machine:

Failures not covered by guarantee

-Replacing worn or damaged blades

-Failures as a result of not reporting an initial fault.

-Failures as a result of sudden impact.

-Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator’s Manual.

-Machines used for hire are not covered by this gua- rantee.

-The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Blades, Electric Mains cable, Belt

-Caution!

Husqvarna Outdoor Products does not accept liability under the warranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Husqvarna Outdoor Products, or by the machine having been modified in any way..

EC DECLARATION OF CONFORMITY

I, the undersigned Bengt Ahlund, of Husqvarna Outdoor Products Italia Spa, Via Como 72, 23868 Valmadrera (LC) Certify that the Lawnmower:-

Category	Electric Wheeled Rotary
Make	Husqvarna Outdoor Products

Products Conforms to the specifications of Directive 2000/14/EEC

I, the undersigned Bengt Ahlund, of Husqvarna Outdoor Products Italia Spa, Via Como 72, 23868 Valmadrera (LC) Certify that a sample of the above product has been tested using directive 81/1051/EEC as a guide. The maximum Aweighted sound pressure level recorded at operator position under free field semi anechoic chamber conditions was:-

I, the undersigned Bengt Ahlund, of Husqvarna Outdoor Products Italia Spa, Via Como 72, 23868 Valmadrera (LC) Certify that a sample of the above product has been tested using ISO 5349 as a guide. The maximum weighted root mean square value of vibration recorded at operator’s hand position was:-

Type of Cutting Device	Rotary Blade
Identification of Series	See Product Rating Label
Conformity Assesment Procedure	ANNEX VI
Notified Body	NEMKO Spa
Other Directives:	98/37/EEC, 2004/108/EEC, 2006/95/EEC
& applicable standards:	EN60555-2:1987, EN60555-3:1987, EN55014:1993, EN55014:1995,

EN836:1997, IEC335-1:1991, IEC335-2-77:1996
Type	A
Version	B
Width of cut	C
Guaranteed sound power level	D
Measured sound power level	E
Sound pressure livel at the ear	F
Vibration of the handle	G

Technical Manager

Husqvarna Outdoor Products Italia spa Via Como 72 - 23868 Valmadrera (LC)

ENGLISH - 5