Access by Digital Modem, 408 654 2706 or 408 654 | 3Com 09-1324-000

B-2APPENDIX B: TECHNICAL SUPPORT

Country	Data Rate	Telephone Number

Mexico	up to 28800 bps	52 5 520 7853
P.R. of China	up to 14400 bps	86 10 684 92351
Singapore	up to 14400 bps	65 534 5693
Taiwan, R.O.C.	up to 14400 bps	886 2 377 5840
U.K.	up to 28800 bps	44 1442 438278
U.S.A.	up to 28800 bps	1 408 980 8204

Access by Digital Modem

ISDN users can dial in to 3ComBBS using a digital modem for fast access up to

56 Kbps. To access 3ComBBS using ISDN, use one of the following numbers:

408 654 2706 or 408 654 2703

3ComFacts Automated 3Com Corporation’s interactive fax service, 3ComFacts, provides data sheets, Fax Service technical articles, diagrams, and troubleshooting instructions on 3Com products

24 hours a day, 7 days a week.

Call 3ComFacts using your Touch-Tone telephone using one of these international access numbers:

Country	Telephone Number

U.K.	44 1442 438279
U.S.A.	1 408 727 7021

Local access numbers are available within the following countries:

	Telephone
Country	Number

Australia	1800 678 515
Belgium	0800 71279
Denmark	800 17319
Finland	98 001 4444
France	05 90 81 58
Germany	0130 81 80 63
Hong Kong	800 933 486
Italy	1678 99085
Malaysia	1800 801 777

	Telephone
Country	Number

Netherlands	06 0228049
New Zealand	0800 446 398
Norway	800 11062
Portugal	0505 442 607
Russia (Moscow only)	956 0815
Singapore	800 6161 463
Spain	900 964 445
Sweden	020 792954
U.K.	0800 626403

3ComForum on 3ComForum contains patches, software, drivers, and technical articles about all CompuServe Online 3Com products, as well as a messaging section for peer support. To use

Service 3ComForum, you need a CompuServe account.

To use 3ComForum:

1Log on to your CompuServe account.

2Type go threecom

3Press [Return] to see the 3ComForum main menu.

Image 68

3Com 09-1324-000 manual Access by Digital Modem, 408 654 2706 or 408 654, Press Return to see the 3ComForum main menu

Contents

New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145 Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide Introduction Conventions List conventions that are used throughout this guideIcon Alerts you to Convention Description Overview Designated as drive a Installation Checklists Software Install System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed 4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory Card Making a Backup Flash MemoryCard NETBuilder II System Using the Backup Flash CardFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand Changes Conﬁguring Primary Boot SourcePrimary boot source Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II System Installing Software From a NetworkManagement Station CD-ROM drive Procedure At the network management station If you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enter Station Prerequisites Tftp CD-ROM Booting a NETBuilder II ImageOver the Network Station Image/NBII/SW/101/FF/boot.29k Conﬁguring IP Copying the SoftwareTo a Flash Memory Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commands FW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page System Configuring Basic SettingsLogging on to Interface Learning AboutUser Interface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form Syntax Abbreviated Syntax SymbolsSymbolDescription Can be abbreviated to Symbol DescriptionFull and Abbreviated Syntax Examples Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual Ports Display it ﬁrst Using AliasesCommand History Substitution Privilege Level Syntax for Assigning Values Numeric ValuesNames Strings Port and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identiﬁes a virtual circuit on the FrameAn example of a Frame Relay address @22 Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678 Syntax Description Getting HelpDescribed in Table Level Obtaining NetworkManager Privilege Password Setting the TimeChanging Date Information Setting SystemAdministrator Assigning Internet AddressesAssigning Internet Addresses to a Bridge Internet addresses to individual ports using SETDefault !2 -IP NETaddr = 22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings TFTP/FTP Server Booting the Netbuilder II CEC a 20 System from the NetworkBooting from a NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Services ServiceAccess by Analog Modem Technical Support Press Return to see the 3ComForum main menu Access by Digital Modem408 654 2706 or 408 654 Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com Canada Regional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com Mediterraneo Index Numerics ﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty