Contents | 3Com 09-1324-000 specs

CONTENTS

ABOUT THIS GUIDE

Introduction

1

How to Use This Guide 1

Conventions 2

1 OVERVIEW

NETBuilder II Systems	1-1
EZBuilt Preassembled NETBuilder II System		1-1
Component System	1-1
NETBuilder II Chassis with a DPE Module		1-1
NETBuilder II Chassis with a CEC 20 Module 1-1
Software 1-2
Installation Checklists	1-2
NETBuilder II Systems with a DPE Module		1-3
NETBuilder II Systems
with a CEC 20 Module 1-4

2INSTALLING SOFTWARE AND BOOTING A DPE NETBUILDER II SYSTEM

Installing Software and Performing Initial Boot		2-1
Booting from the Flash Memory Card 2-1
Prerequisites	2-1
Booting an EZBuilt NETBuilder II System 2-1
Booting a Component NETBuilder II System		2-2
Making a Backup of the Flash Memory Card		2-2
Prerequisites	2-2
Procedure	2-2

Using the Backup Flash Card 2-3

3CHANGING THE BOOT SOURCE ON A DPE NETBUILDER II SYSTEM

Using the Boot Command 3-1

Conﬁguring the Primary Boot Source 3-2

Prerequisites 3-2

Procedure 3-2

4INSTALLING SOFTWARE AND BOOTING A CEC 20 NETBUILDER II SYSTEM

Installing Software and Performing Initial Boot	4-1
Booting from the Flash Memory Card 4-1
Prerequisites 4-1
Booting an EZBuilt NETBuilder II System	4-1

iii

Image 3

3Com 09-1324-000 manual Contents

Contents

New Installation for NETBuilder II Software 95052-8145 3Com CorporationBayfront Plaza Santa Clara, California Contents CEC 20 System Index 3COM Corporation Limited Warranty Page Introduction About this Guide Convention Description ConventionsList conventions that are used throughout this guide Icon Alerts you to Designated as drive a Overview Software Installation Checklists Change the primary boot source default as needed Install System Software and Boot Refer to ChapterInstall software from a flash memory card Change the Primary Boot Source Refer to Chapter 4CHAPTER 1 Overview Memory Card Installing Software and Booting DPE Netbuilder II SystemInstalling Software Performing Initial Boot Booting from the Flash NETBuilder II System Making a BackupFlash Memory Card Following these steps Using the BackupFlash Card Format the blank ﬂash memory card in drive B by enteringPage Changes Changing the Boot Source on aUsing the Boot Command Primary Boot Source Primary boot sourceConﬁguring Configuring the Primary Boot Source Page CEC 20 Netbuilder II System Installing Software and Booting CD-ROM drive Installing SoftwareFrom a Network Management Station At the network management station Procedure To see if these daemons are running, enter If you are using a Bourne sh or Korn ksh shell, enter Tftp CD-ROM Station Prerequisites Station Booting aNETBuilder II Image Over the Network Image/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConﬁguring IP Format the blank ﬂash memory card by entering Enter a routing protocol For example, enable RIP usingPage You are now ready to enter software commands Slot 7 as the primary boot source FW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Full-Form Syntax Reference for NETBuilder Family Software Symbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Determining the Display of Ports and Virtual Ports Variations in Command SyntaxEntering Service Names in Command Lines Can be shortened by abbreviating it to Using Aliases Command History SubstitutionDisplay it ﬁrst Privilege Level Strings Syntax for Assigning ValuesNumeric Values Names Port and Path Naming Restrictions Media Addresses @22 Asynchronous Transfer Mode ATM addressDecimal. The Dlci identiﬁes a virtual circuit on the Frame An example of a Frame Relay address Network Layer Addresses Addresses are the same 00003333%080002005678 For more information on Internet addresses, subnet masks,Followed by the MAC address Network from all other IPX networks. The following example Getting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Date PasswordSetting the Time Changing Setting System AdministratorInformation Addresses to a Bridge Assigning InternetAddresses Assigning Internet SETDefault !2 -IP NETaddr = Internet addresses to individual ports using 22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Technical Support ServicesService Access by Analog Modem Access by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu 3Com Canada Regional Sales Office Telephone Number 3Com Corporation3Com Asia Limited Regional Sales Office Telephone Number 3Com Benelux B.V Regional Sales Office Telephone Number 3Com Mediterraneo Regional Sales Office Telephone Number 3Com Iberia3Com Ireland 3Com Latin America Numerics Index ﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty