3Com 09-1324-000 instruction

2-4CHAPTER 2: INSTALLING SOFTWARE AND BOOTING A DPE NETBUILDER II SYSTEM

3Reboot the NETBuilder II bridge/router by pressing the two outer buttons on the LCD control panel.

The system boots from the NETBuilder II software flash memory card in drive A.

4Make a copy of the ﬂash memory card in drive A by following the steps in the previous procedure.

You will need to either obtain an additional ﬂash memory card or reformat the corrupted ﬂash memory card. If you choose to reformat a corrupted ﬂash memory card, inspect the card to make sure that it is not damaged. Always keep the original NETBuilder II software flash memory card in a safe place and protect it from accidental damage.

Image 16

3Com 09-1324-000 manual

Contents

New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145 Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide Introduction Conventions List conventions that are used throughout this guideIcon Alerts you to Convention Description Overview Designated as drive a Installation Checklists Software Install System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed 4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory Card Making a Backup Flash MemoryCard NETBuilder II System Using the Backup Flash CardFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand Changes Primary boot source Primary Boot SourceConﬁguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II System Installing Software From a NetworkManagement Station CD-ROM drive Procedure At the network management station If you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enter Station Prerequisites Tftp CD-ROM Booting a NETBuilder II ImageOver the Network Station Image/NBII/SW/101/FF/boot.29k To a Flash Memory Copying the SoftwareConﬁguring IP Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commands FW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Logging on to Configuring Basic SettingsSystem User Interface Learning AboutInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form Syntax SymbolDescription SymbolsAbbreviated Syntax Full and Abbreviated Syntax Examples Symbol DescriptionCan be abbreviated to Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual Ports Command History Substitution Using AliasesDisplay it ﬁrst Privilege Level Syntax for Assigning Values Numeric ValuesNames Strings Port and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identiﬁes a virtual circuit on the FrameAn example of a Frame Relay address @22 Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678 Described in Table Getting HelpSyntax Description Manager Privilege Obtaining NetworkLevel Password Setting the TimeChanging Date Administrator Setting SystemInformation Assigning Internet AddressesAssigning Internet Addresses to a Bridge Internet addresses to individual ports using SETDefault !2 -IP NETaddr = 22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting from a Booting the Netbuilder II CEC a 20 System from the NetworkTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Services ServiceAccess by Analog Modem Technical Support 408 654 2706 or 408 654 Access by Digital ModemPress Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com Canada Regional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com Mediterraneo Index Numerics ﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty