24CHAPTER 6 Configuring Basic Settings | 3Com 09-1324-000 manual

6-24CHAPTER 6: CONFIGURING BASIC SETTINGS

Security Commands and To make sure that some designated ﬁles are accessible only to the system Parameters administrator, use the following commands and parameters:

■NetAccess

This parameter is a SYS Service parameter that determines how a bridge/router can be accessed from another device on the network. For information on how to use the NetAccess parameter, refer to Using NETBuilder Family Software and to Reference for NETBuilder Family Software.

■SysPassWord

This command brings up a menu allowing you to specify the password for the Network Manager and User privilege levels. For information on how to use the SysPassWord command, refer Reference for NETBuilder Family Software.

■RemoteManager

This parameter is a SYS Service parameter that speciﬁes the Internet addresses of devices that can connect to the bridge/router through the REMote command. For information on how to use the RemoteManager parameter, refer to Using NETBuilder Family Software and to Reference for NETBuilder Family Software.

■COMmunity

This parameter is an SNMP Service parameter that modiﬁes the list of communities. For information on how to use the COMmunity parameter, refer to Using NETBuilder Family Software and to Reference for NETBuilder Family Software.

What Next?You are now ready to refer to Using NETBuilder Family Software to conﬁgure your bridge/router for your speciﬁc network needs.

Image 60

3Com 09-1324-000 manual 24CHAPTER 6 Configuring Basic Settings

Contents

New Installation for NETBuilder II Software 3Com Corporation Bayfront Plaza SantaClara, California 95052-8145 Contents CEC 20 System Index 3COM Corporation Limited Warranty Page About this Guide Introduction Conventions List conventions that are used throughout this guideIcon Alerts you to Convention Description Overview Designated as drive a Installation Checklists Software Install System Software and Boot Refer to Chapter Install software from a flash memory cardChange the Primary Boot Source Refer to Chapter Change the primary boot source default as needed 4CHAPTER 1 Overview Installing Software and Booting DPE Netbuilder II System Installing Software Performing Initial BootBooting from the Flash Memory Card Making a Backup Flash MemoryCard NETBuilder II System Using the Backup Flash CardFormat the blank ﬂash memory card in drive B by entering Following these stepsPage Changing the Boot Source on a Using the BootCommand Changes Primary Boot Source Primary boot sourceConﬁguring Configuring the Primary Boot Source Page Installing Software and Booting CEC 20 Netbuilder II System Installing Software From a NetworkManagement Station CD-ROM drive Procedure At the network management station If you are using a Bourne sh or Korn ksh shell, enter To see if these daemons are running, enter Station Prerequisites Tftp CD-ROM Booting a NETBuilder II ImageOver the Network Station Image/NBII/SW/101/FF/boot.29k Copying the Software To a Flash MemoryConﬁguring IP Enter a routing protocol For example, enable RIP using Format the blank ﬂash memory card by enteringPage Slot 7 as the primary boot source You are now ready to enter software commands FW/NBII-FW,2.6 Enter 4 to select Primary Boot Source To select NETBuilder software version 10.1 enter Secondary Boot Source Page Configuring Basic Settings Logging on toSystem Learning About User InterfaceInterface Main menu Level 1 is displayed Reference for NETBuilder Family Software Full-Form Syntax Symbols SymbolDescriptionAbbreviated Syntax Symbol Description Full and Abbreviated Syntax ExamplesCan be abbreviated to Variations in Command Syntax Entering Service Names in Command LinesCan be shortened by abbreviating it to Determining the Display of Ports and Virtual Ports Using Aliases Command History SubstitutionDisplay it ﬁrst Privilege Level Syntax for Assigning Values Numeric ValuesNames Strings Port and Path Naming Restrictions Media Addresses Asynchronous Transfer Mode ATM address Decimal. The Dlci identiﬁes a virtual circuit on the FrameAn example of a Frame Relay address @22 Network Layer Addresses For more information on Internet addresses, subnet masks, Followed by the MAC addressNetwork from all other IPX networks. The following example Addresses are the same 00003333%080002005678 Getting Help Described in TableSyntax Description Obtaining Network Manager PrivilegeLevel Password Setting the TimeChanging Date Setting System AdministratorInformation Assigning Internet AddressesAssigning Internet Addresses to a Bridge Internet addresses to individual ports using SETDefault !2 -IP NETaddr = 22CHAPTER 6 Configuring Basic Settings Enable the Snmp service by entering 24CHAPTER 6 Configuring Basic Settings Booting the Netbuilder II CEC a 20 System from the Network Booting from aTFTP/FTP Server NETBuilder Software on the Unix NMS Enter Q to return to the Primary Boot Source menu Table A-1Additional Tftp Primary Boot Source Parameters Parameter Conﬁguration Token ring port Page Services ServiceAccess by Analog Modem Technical Support Access by Digital Modem 408 654 2706 or 408 654Press Return to see the 3ComForum main menu Regional Sales Office Telephone Number 3Com Corporation 3Com Asia LimitedRegional Sales Office Telephone Number 3Com Benelux B.V 3Com Canada Regional Sales Office Telephone Number 3Com Iberia 3Com Ireland3Com Latin America Regional Sales Office Telephone Number 3Com Mediterraneo Index Numerics ﬁrmware 4-6,A-4,A-5 3Com Corporation Limited Warranty