3Com 10014298 - page 141

Configuring PIM-SM 141

If static RP is in use, all routers in the PIM domain must adopt the same

configuration. If the configured static RP address is the interface address of the

local router whose state is UP, the router will function as the static RP. It is

unnecessary to enable PIM on the interface that functions as static RP.

When the RP elected from BSR mechanism is valid, static RP does not work.

Configuring the Interface Hello Message Interval

Generally, PIM-SM advertises Hello messages periodically on the interface enabled

with it to detect PIM neighbors and discover which router is the Designated Router

(DR).

Perform the following configuration in VLAN interface view.

By default, the hello message interval is 30 seconds. Users can configure the value

according to different network environments.

This configuration can be performed only after the PIM (PIM-DM or PIM-SM) is

enabled in VLAN interface view.

Configuring the Filtering of Multicast Source/Group

See “Configuring PIM-DM” on page 130.

Configuring the Filtering of PIM Neighbor

See “Configuring PIM-DM” on page 130.

Configuring the Maximum Number of PIM Neighbor on an Interface

See “Configuring PIM-DM” on page 130.

Configuring RP to Filter the Register Messages Sent by DR

In the PIM-SM network, the register message filtering mechanism can control

which sources to send messages to, which groups on the RP, i.e., RP can filter the

register messages sent by DR to accept specified messages only.

Perform the following configuration in PIM view.

If an entry of a source group is denied by the ACL, or the ACL does not define

operation to it, or there is no ACL defined, the RP will send RegisterStop messages

to the DR to prevent the register process of the multicast data stream.

Tabl e 151 Configuring the Interface Hello Message Interval

Operation Command

Configure the interface hello message interval pim timer hello seconds

Restore the interval to the default value undo pim timer hello

Tabl e 152 Configuring RP to Filter the Register Messages Sent by DR

Operation Command

Configure RP to filter the register messages

sent by DR

register-policy acl-number

Cancel the configured filter of messages undo register-policy

Contents

Main 3Com Corporation 350 Campus Drive Marlborough, MA 01752-3064 C ABOUT THIS GUIDE S YSTEM A PORT CONFIGURATION VLAN C IP ROUTING PROTOCOL OPERATION M ULTICAST P QOS/ OPERATION STP O AAA AND RADIUS OPERATION SYSTEM MANAGEMENT Page Page ABOUT THIS GUIDE This guide describes the 3Com Switch 7750 and how to configure it in version 3.0 of the software. Tabl e 2 lists the text conventions used in this book. Conventions Tabl e 1 Notice Icons Table 2 Text Conventions 1 Product Overview Configuring the Switch 7750 Figure 1 Setting Up the Local Configuration Environment Through the Console Port Table 3 Function Features (continued) Page Page Page Ethernet Page Page Page Page Page Page Page Page Page Page Page Command Line Interface Page Tabl e 20 Function Feature of Command View Page Page Tabl e 23 Editing Functions Tabl e 24 Display Functions Table 22 Retrieve History Command Page 2 Ethernet Port Overview Page Page Page Page Page Page Configuring Link Aggregation Page Page Page Page Page Page Perform the following configuration in Ethernet port view. Tabl e 44 Configure Port Priority Tabl e 45 Display and Debug Link Aggregation Page Page Page 3 VLAN Overview Configuring VLANs Page Page Page Page Page Page 3Configure the protocol VLAN on port G1/0/1 Configuring GARP/GVRP Page Page Page Page Page 4 Configuring IP Address Page Page Configuring Address Resolution Protocol (ARP) Page DHCP Relay Page Page Page Page IP Performance Page Page Page 5 IP Routing Protocol Overview Page Page Static Routes Page Page Page Page RIP Page Page Page Page Page Page Page Page Page IP Routing Policy Page Page Page Page Page Route Capacity Page Page Page 6 IP Multicast Overview Page Page Page Page Configuring Common Multicast Page Configuring IGMP Page Page Page Page Page Page Page IGMP Snooping Page Page Page Page Page Configuring PIM-DM Page Page Page Page Figure 33 PIM-DM Configuration Networking 2Enable PIM-DM. Table 144 Displaying and Debugging PIM-DM Configuring PIM-SM Page Page Page Page Page Page Page Execute the debugging command in user view to debug PIM-SM. Figure 35 PIM-SM Configuration Networking Configure Switch A 1Enable PIM-SM. Tabl e 157 Display and Debug PIM-SM Configure Switch B 1Enable PIM-SM. 2Configure the C-BSR. 3Configure the C-RP. 4Configure PIM domain border. GMRP Page Page 7 ACL Overview Page Configuring ACLs Page Page Page ACL Configuration Examples Page Configuring QoS Page Page Page Page Page Page Page Page Page Tabl e 183 Configuring Traffic Statistics Tabl e 184 Display and Debug QoS Page Page Page Page Page Page Page Configuring ACL Control Page Page Page Page Page 8 STP Overview Configuring STP Page Page Page Page MSTP Overview Page Page Configuring MSTP Page Page Page Page Page Page Page Page Page Perform the following configuration in system view. By default, the switch calculates the default Path Cost of a port by the IEEE 802.1t standard. Tabl e 204 Specifying the Standard To Be Followed in Path Cost Calculation Tabl e 205 Cost Corresponding to the Port Speed of Different Standard Page Page Page Page Page Digest Snooping Page 9 IEEE 802.1x Page Page Page Page Page Page Page Implementing the AAA and RADIUS Protocols Page Configuring AAA Page Page Configuring the RADIUS Protocol Page Page Page Page Page Page Page Page Page Configuring HWTACACS Page Page Page Page Page Page The real-time accounting interval defaults to 12 minutes. Displaying and Debugging the AAA, RADIUS, and HWTACACS Protocols Table 255 Numbers of users and the recommended intervals Tabl e 256 Displaying and Debugging AAA and RADIUS/HWTACACS Protocol AAA, RADIUS, and HWTACACS Protocol Configuration Examples Page Page Troubleshooting AAA, RADIUS, and HWTACACS Configurations Page 11 File System Page Page Page Page Page Managing the MAC Address Table Page Page Page Managing Devices Page Maintaining and Debugging the System Page Page Page Page Page Page The system assigns a channel in each output direction by default. See Tabl e 293. Tabl e 293 Numbers and Names of the Channels for Log Output Tabl e 294 Syslog-Defined Severity Table 292 Log Output (continued) Page Page SNMP Page Page Page Page Page Page Tabl e 310 Enable/Disable Transmission of Trap Information Tabl e 311 Disabling SNMP Agent Tabl e 312 Displaying and Debugging SNMP Page RMON Page Page Page NTP Page Page Page Page Page Page Page Page After the synchronization, SW77502 turns into the following status: