A&D HG-60KGV, HW-100KGL, HW-10KGL, HW-10KGV, HW-200KGL, HW-200KGV, HW-60KGL, HW100KGV

HW-G Instruction Manual Page 67 HW-G OZIM v1a

Contents

Main Page Contents Page 1 Compliance 1.1 Compliance with FCC rules 2 Outline and Features HW-G Instruction Manual Page 5 3 Unpacking All Accessories 3.1 Accessories and Options list Accessories for HW-G series Page 4 Caution 4.1 Precautions for Installing the Scale 4.2 Precautions for Operating the Scale 4.3 Precautions for Storing the Scale 5 Installing the Scale Page 5.1 Installing the Batteries for Type L 6 Names 6.1 Display and Symbols Page 6.2 Switches Page 7 Basic Operation 7.1 Turning the Scale On/Off & Basic Weighing 7.1.1 Type V or Type L with AC adaptor 7.1.2 Type L with Batteries 7.2 Tare (and Net Display) 7.2.1 Semi-Automatic Tare (Input by Weighing) 7.2.2 Preset Tare (Digital Input of Known Tare) HW-G Instruction Manual Page 20 7.3 Mode Switch (Changing Unit & Mode) 8 Counting Mode 8.1 Storing a Unit Mass 8.2 Counting the number of articles 9 Percentage Mode 9.1 Storing a 100% Mass 9.2 Reading Percentage 10 Accumulation Function Caution 10.1 Preparation (Setting Parameters) 10.2 Operation and Performance (Examples) Example 1 Example 2 11 Comparator Function Comparator Sign Comparison Condition 11.1 Preparation (Setting Parameters) Page 11.2 Operation and Performance (Examples) Example 1 Case Example 2 Case 12 Full/Dribble Batch Function Caution 12.1 Preparation (Setting Parameters) Page 13 Simple Batch Function Comparison Condition Parameter List and Word Definition 13.1 Preparation (Setting Parameters) 13.2 Operation and Performance (Examples) 14 Calibration (Adjusting the Scale) Caution 14.1 The Gravity Acceleration Table 14.2 The Complete Calibration Procedure 14.2.1 Gravity Acceleration Correction 14.2.2 Preparation 14.2.3 Calibration of the Zero Point 14.2.4 Span Calibration 15 The Function Table 15.1 The Procedure for Setting Parameters 15.2 Parameter List The type L scale is turned off after 5 minutes of no operation, when displaying zero. Transmission rate of the serial interface (RS-232C/ 422/485). Mode selection for the serial interface (RS-232C/ 422/485). Mode selection for the comparator The condition of the buzzer on option OP-03 by comparator function or full/dribble batch function. The condition of the accumulator The printing condition when using option OP-06 for type V. The details of the full/dribble batch function ( ) Address for RS-422 / RS-485 for option OP-04 Page 16 RS-232C Serial Data Interface 16.1 Data Format Bit Format Format 1 Format 2 Caution 16.2 Stream Mode 16.2.1 Preparation and Performance (Examples) 16.3 Command Mode 16.3.1 Command List Selects the mode and unit. This is the same as the The current weighing data is output. The current mass value is set to the zero point. Page Page 16.4 Preparation (Setting Parameters) 17 Options 17.1 RS-232C / Relay output / Buzzer (OP-03) Installing OP-03 17.2 RS-422 / RS-485 / Relay output (OP-04) Page 17.2.1 Communication Format Bit format Selects the mode and unit. This is same as the 17.2.2 Command List Data output Zero Tare Caution The lower limit value must be less than the upper limit value. Cancel of tare Preset tare Page 17.3 Internal Printer for Type V (OP-06) Specification Consumables Operation and Print Samples Installation of OP-06 Installation Method Page HW-G series Page Page 19 Maintenance 19.1 Repair 19.2 Check Points Before Calling Maintenance

A&D - page 69

Models: HG-60KGV HW-100KGL HW-10KGL HW-10KGV HW-200KGL HW-200KGV HW-60KGL HW100KGV