Allied Telesis AT-WR4500 manual Dual Nstreme, Monitor the link, Ssid nstreme

AT-WR4500 Series - IEEE 802.11abgh Outdoor Wireless Routers	67
RouterOS v3 Configuration and User Guide

Configure Nstreme-Clientwireless settings and enable Nstreme on it:

[admin@Nstreme-Client] interface wireless> set wlan1 mode=station ssid=nstreme \ band=5ghz frequency=5805 disabled=no

[admin@Nstreme-Client] interface wireless> print Flags: X - disabled, R - running

0name="wlan1" mtu=1500 mac-address=00:0B:6B:34:5A:91 arp=enabled disable-running-check=no interface-type=Atheros AR5213 radio-name="000B6B345A91" mode=station ssid="nstreme" area="" frequency-mode=superchannel country=no_country_set antenna-gain=0 frequency=5805 band=5ghz scan-list=default rate-set=default supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps

supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps, 54Mbps

basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 ack-timeout=dynamic tx-power=default tx-power-mode=default noise-floor-threshold=default periodic-calibration=default burst-time=disabled fast-frames=no dfs-mode=none antenna-mode=ant-a wds-mode=disabled wds-default-bridge=none wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no security-profile=default disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both

[admin@Nstreme-Client] interface wireless> nstreme

[admin@Nstreme-Client] interface wireless nstreme> set wlan1 enable-nstreme=yes

[admin@Nstreme-Client] interface wireless nstreme> print

0 name="wlan1" enable-nstreme=yes enable-polling=yes framer-policy=none framer-limit=3200

[admin@Nstreme-Client] interface wireless nstreme>

And monitor the link:

[admin@Nstreme-Client] interface wireless> monitor wlan1 status: connected-to-ess

band: 5ghz frequency: 5805MHz tx-rate: 24Mbps rx-rate: 18Mbps

ssid: "nstreme"

bssid: 00:0C:42:05:00:22 radio-name: "000C42050022"

signal-strength: -70dBm tx-signal-strength: -68dBm

tx-ccq: 0%

rx-ccq: 3% wds-link: no nstreme: yes polling: yes framing-mode: none routeros-version: "3.2"

current-tx-powers: 1Mbps:11,2Mbps:11,5.5Mbps:11,11Mbps:11,6Mbps:28, 9Mbps:28,12Mbps:28,18Mbps:28,24Mbps:28,36Mbps:25, 48Mbps:23,54Mbps:22

--[Q quitD dumpC-z pause] [admin@Nstreme-Client] interface wireless>

Dual Nstreme

The purpose of Nstreme2 (Dual Nstreme) is to make superfast point-to-point links, using 2 wireless interfaces on each router - one for receiving and the other one for transmitting data (you can use different bands for receiving and transmitting). This example will show you how to make a point-to-point link, using Dual Nstreme.