Allied Telesis AT-WR4500 manual WPA Security, Admin@WEPStationX interface wireless

AT-WR4500 Series - IEEE 802.11abgh Outdoor Wireless Routers	73
RouterOS v3 Configuration and User Guide

Config of WEP_StationX:

[admin@WEP_StationX] interface wireless security-profiles> add name=StationX \ \... mode=static-keys-required static-algo-1=40bit-wep static-key-1=1234567890 \ \... static-transmit-key=key-1

[admin@WEP_StationX] interface wireless security-profiles> print

0 name="default" mode=none wpa-unicast-ciphers="" wpa-group-ciphers="" pre-shared-key="" static-algo-0=none static-key-0="" static-algo-1=none static-key-1="" static-algo-2=none static-key-2="" static-algo-3=none static-key-3="" static-transmit-key=key-0 static-sta-private-algo=none static-sta-private-key="" radius-mac-authentication=no group-key-update=5m

1 name="StationX" mode=static-keys-required wpa-unicast-ciphers="" wpa-group-ciphers="" pre-shared-key="" static-algo-0=none static-key-0="" static-algo-1=40bit-wep static-key-1="1234567890" static-algo-2=none static-key-2="" static-algo-3=none static-key-3="" static-transmit-key=key-1 static-sta-private-algo=none static-sta-private-key="" radius-mac-authentication=no group-key-update=5m

[admin@WEP_StationX] interface wireless security-profiles> ..

[admin@WEP_StationX] interface wireless> set wlan1 name=WEP-STAX ssid=mt_wep \ \... band=5ghz security-profile=StationX mode=station disabled=no [admin@WEP_StationX] interface wireless> print

0R name="WEP-STAX" mtu=1500 mac-address=00:0C:42:05:06:B2 arp=enabled disable-running-check=no interface-type=Atheros AR5413 radio-name="000C420506B2" mode=station ssid="mt_wep" area="" frequency-mode=superchannel country=no_country_set antenna-gain=0 frequency=5180 band=5ghz scan-list=default rate-set=default

supported-rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps supported-rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,

54Mbps

basic-rates-b=1Mbps basic-rates-a/g=6Mbps max-station-count=2007 ack-timeout=dynamic tx-power=default tx-power-mode=default noise-floor-threshold=default periodic-calibration=default burst-time=disabled fast-frames=no dfs-mode=none antenna-mode=ant-a wds-mode=disabled wds-default-bridge=none wds-ignore-ssid=no update-stats-interval=disabled default-authentication=yes default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no security-profile=StationX disconnect-timeout=3s on-fail-retry-time=100ms preamble-mode=both

[admin@WEP_StationX] interface wireless>

WPA Security

This example shows WPA (Wi-Fi Protected Access) configuration on Access Point and Client to secure all data which will be passed between AP and Client

	[WPA_AP]
	Interface: wlan1
	ssid=AT-WR4500
Interface: wlan1	Pre-shared-key=1234567890
Pre-shared-key=1234567890	Wpa-group-cipher=aes-ccm
	Wpa-unicast-cipher=tkip
Wpa-group-cipher=aes-ccm
Wpa-unicast-cipher=tkip [WPA_Station]

Figure 10: WPA security example