Manuals / Amana / Kitchen Appliance / Range

Amana RSS service manual Door Glass - Inner, OVEN DOOR GLASS - PORCELAIN DOOR Model RST354

Models: RST RSS

1 124

Download 124 pages 42.19 Kb

Page 99

DOOR GLASS - INNER

DISASSEMBLY PROCEDURES - RST MODELS

FIRE OR EXPLOSION - TO AVOID THE RISK OF ELECTRICAL SHOCK, PERSONAL INJURY, OR DEATH, DISCONNECT POWER TO THE OVEN BEFORE SERVICING.

DOOR GLASS - INNER

1.Remove oven door assembly from the range and place door on a protected surface.

2.Remove the six (6) screws securing the oven door backer to the oven door frame. On Model RST354 the backer is attached to the outer door frame.

3.Remove two (2) screws securing heat shield to door backer.

4.Remove the fourteen (14) screws securing the door backer to the sub backer. Gently remove door backer. NOTE POSITION OF DOOR GASKET FOR CORRECT REASSEMBLY.

5.Remove insulation and the eight (8) screws securing the window assembly to the door backer.

6.Gently remove window assembly.

7.Reverse procedure to reinstall.

When reassembling, be sure hinge pins and rubber bumpers are in place.

Figure 89

OVEN DOOR GLASS - PORCELAIN DOOR Model RST354

1.Remove oven door from range and place it on a protected surface.

2.Remove six (6) screws securing door backer to outer door panel and remove panel.

3.Remove screws securing glass retaining clips to outer panel and remove glass.

4.Reverse procedure to reinstall.

STORAGE DRAWER PANEL, STORAGE CDRAWER BACKER, STORAGE DRAWER, STORAGE DRAWER TRACKS (RSS MODELS)

1.Pull storage drawer all the way out - lift up on runner (gray - left, black - right) arms inside then pull storage drawer all the way out and off or range.

2.Tracks are fastended to side frame with a screw.

3.Runners are fastened to storage drawer by two (2) pop rivets on each side.

4.Storage drawer panel and storage drawer backer are secured to storage drawer using screws.

STORAGE DRAWER PANEL (RST MODELS)

1.Remove storage drawer from range.

2.Remove six (6) screws securing outer panel to drawer panel liner.

3.To replace the panel, remove four (4) screws secur- ing drawer handle to panel.

STORAGE DRAWER HANDLE (RST MODELS)

1.To remove the handle, using the Storage Drawer Panel Removal Procedure.

RC231002 Rev. 3

98

Image 99

Amana RSS Door Glass - Inner, OVEN DOOR GLASS - PORCELAIN DOOR Model RST354, Storage Drawer Panel Rst Models

Contents

Service RST and RSS Gas RangesModels and manufacturing numbers in this manual see page 2A REPLACE MANUAL 56397 AND 56074 WITH THIS MANUAL, RC231002 INDEXMODEL MODEL AND MANUFACTURING NUMBERSRECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS IMPORTANT NOTE TO CONSUMERIMPORTANT INFORMATION CALORIC MODEL DESCRIPTION BREAKDOWN GENERAL INFORMATIONGENERAL INFORMATION MODEL IDENTIFICATIONGENERAL INFORMATION RECEIVINGCARE AND HANDLING OF PORCELAIN ENAMEL CARE AND HANDLING OF CHROME, GLASS, OR METAL FINISHGENERAL INFORMATION SPECIFICATIONS - Burner Ratings - RSTSPECIFICATIONS - Burner Ratings - RSS ELECTRICAL REQUIREMENTSMODELS MUST NOT EXCEED 14-INCHES W.C.P INSTALLATION INSTRUCTIONSSUGGESTED LOCATION OF SERVICE PIPE - REAR WALL OR FLOOR THE MAXIMUM GAS SUPPLY PRESSURE FOR THESEINSTALLATION Location SECURE RANGE TO HOUSE STRUCTUREINSTALLATION INSTRUCTIONS FOR GROUNDING - THIS APPLIANCE MUST BE Where a standard two-prong wall receptacle is enIN MOBILE HOMES ELECTRICAL CONNECTIONSTEST FOR GAS LEAKS CONNECTING TO GAS SUPPLY LINEFIRE OR EXPLOSION HAZARD FIRE OR EXPLOSION HAZARD - LEAK TEST COMPONENTS AFTER CONNECTIONFigure9 INSTALLATION INSTRUCTIONS FOR ANTI-TIPTo Install Anti-Tip Bracket, Carefully Follow these Instructions BRACKETNATURAL GAS BURNER ADJUSTMENT CABINET INSTALLATION OPENING FOR GAS SLIDE-IN RANGE11. Never install a range over kitchen carpeting ADJUSTMENTS AND LP CONVERSION NATURAL GAS BURNER ADJUSTMENTModels with Sealed Top Burners Above Serial Number F0430127550 For Access to the Air ShuttersTo Adjust the Air Shutter UPPER OVEN BURNER ADJUSTMENT - RSTLP CONVERSION NATURAL TO LP GAS CONVERSION FIRE OR EXPLOSIION HAZARD BROIL BURNER Burner AdjustmentUPPER OVEN FLAME CHARACTERISTIC ADJUSTMENT PRESSURE REGULATOR On RangeMODELS WITH SEALED TOP BURNERS MODELS WITHOUT SEALED TOP BURNERS TOP BURNER ADJUSTMENT ORIFICESTOP BURNER ADJUSTMENT Below Serial Number F0430127550 ORIFICES FLAME APPEARANCEMODELS WITH CAST BURNERS BURNER ADJUSTMENTTOP BURNER ADJUSTMENT Above Serial Number F0430127550 TO CONVERT LOWER OVEN FLAME CHARACTERISTIC ADJUSTMENTMODELS WITHOUT SEALED TOP BURNERS RANGE FEATURE CHECKOUTOVEN BURNER RSS ULTRA-RAY BROILER BURNERDEFECTS MAINTENANCE INSTRUCTIONSPOWER FAILURE BURNER CLEANINGModels without electronic Range Control ERC PROTECT YOUR HANDS WHEN REMOVING DRIED BURNERS FORM THE OVENOVEN THERMOSTAT KNOB ADJUSTMENT UNIVERSAL GAS ORIFICESINSTALLATION INSTRUCTIONS USING THE MANOMETERGAS PRESSURE MEASURING GAS PRESSURESAFETY PRECAUTIONS READ BEFORE OPERATING THE RANGE SAFE OPERATING PROCEDURESSAFE OPERATING PROCEDURES OPERATING INSTRUCTIONS SAFETY TIPSBROILING The Ultra-Ray Broiler BAKINGSAFE OPERATING PROCEDURES OPERATING THE TOP BURNERS MODELS WITHOUT SEALED BURNERSTOP BURNERS MODELS WITH SEALED BURNERSTo Set the Minute Timer OPERATION AND SERVICE PROCEDURESSetting the Time-of-Day Setting the Minute TimerOPERATION AND SERVICE PROCEDURES SETTING THE TIME FOR SELF-CLEAN TO START SELF-CLEAN NOWTO START SELF-CLEAN LATER DELAYED TIME BAKESLIDE IN MODELS CLOCK/TIMER TESTING PROCEDURES P.C. BOARD TESTING - NO POWER TO UNITK1 RELAY CONTACT TESTING OPERATION AND SERVICE PROCEDURESCLOCK P.C. BOARD VOLTAGE TESTS OPERATION AND SERVICE PROCEDURESSLIDE IN MODELS OPERATION AND SERVICE PROCEDURES PINSDISPLAY BOARD TESTING VOLTAGEP.C. BOARD/DISPLAY BOARD INTERCONNECT CABLE OPERATION AND SERVICE PROCEDURESSLIDE IN MODELS SLIDE IN MODELS OPERATION AND SERVICE PROCEDURESTROUBLESHOOTING GUIDE SLIDE IN MODELSsimultaneously to set clock tim Figure 35 - Electronic Range Control - ERC To Set Time of Day To Set Minute TimerElectronic Range Control ERC Models w/Two Piece Control To Use the Bake FunctionTo Set Broil Function Electronic Range Control ERC Models w/ Two Piece ControlTo Use the Stop Time Function To Use Stop Time for Delayed Baking FunctionELECTRONIC RANGE CONTROL - ERC To Set for Self-CleanTo Set for Delayed Self-Clean To Use Cancel FunctionERC SYSTEM EXPLANATION TESTING PROCEDURESRELAY/POWER SUPPLY CIRCUIT BOARD TESTING Testing with No Voltage Applied5-7 OHMS OPERATION AND SERVICE PROCEDURESElectronic Range Control ERC Models w/Two Piece Control OHMS READINGSTo check the broil relay contacts, shut off power to the Testing with Voltage AppliedERC OVEN TEMPERATURE SENSOR OPERATION AND SERVICE PROCEDURESElectronic Range Control ERC Models w/Two Piece Control ERC TROUBLESHOOTING FAILURE CODES AND CALIBRATION ERC REMOVALERC VOLTAGE TESTS OPERATION AND SERVICE PROCEDURESElectronic Range Control ERC Models w/ Two Piece Control OPERATION AND SERVICE PROCEDURESELECTRONIC RANGE CONTROL TEMPERATURE CALIBRATION DOOR APPEARS IN DISPLAY DURING CLEAN MODEERC FAILURE CODES AND WARNINGS DOOR APPEARS IN DISPLAY IN BAKE/BROIL MODEElectronic Range Control ERC Models w/Two Piece Control TROUBLE SHOOTING GUIDEElectronic Range Control ERC Models w/Two Piece Control TROUBLE SHOOTING GUIDETROUBLE SHOOTING GUIDE Electronic Range Control ERC Models w/Two Piece ControlE. Display operates normally. Bake or broil relays do not operate TROUBLE SHOOTING GUIDE Electronic Range Control ERC Models w/Two Piece ControlCheck for shorted latch switc OPERATION AND SERVICE PROCEDURES For the Electronic Range Control ERC Models w/Two Piece ControlTo Set Time of Day Electronic Range Control - ERC - Models w/One Piece ControlOPERATING INSTRUCTIONS FOR THE ELECTRONIC RANGE CONTROL ERC NOTE One Piece ControlTo Use Stop Time for Delayed Baking Function Electronic Range Control - ERC Models w/One Piece ControlOPERATION AND SERVICE PROCEDURES To Use the Stop Time FunctionTo Set for Delayed Self-Clean ERC SYSTEM EXPLANATION - One Piece ControlOPERATION AND SERVICE PROCEDURES To Set for Self-CleanElectronic Range Control - ERC Models w/One Piece Control OPERATION AND SERVICE PROCEDURESTESTING PROCEDURES DOOR APPEARS IN DISPLAY DURING CLEAN MODEVOLTMETER LEADS. USE ONLY WELL INSULATED METER CLIPS CARE MUST BE TAKEN WHEN VOLTAGE TESTINGTURN POWER OFF BEFORE ATTACHING ELECTRONIC RANGE CONTROL - Checking Input Voltage and Output VoltageELECTRONIC RANGE CONTROL OPERATION AND SERVICE PROCEDURESElectronic Range Control - ERC Models w/One Piece Control OPERATION AND SERVICE PROCEDURES Electronic Range Control - ERC - Models w/One Piece ControlB. Continuity should be indicated J2 Pin 3 to J2 Pin 4 with door latched. No continuity open circuit Electronic Range Control - ERC Models w/One Piece Control OPERATION AND SERVICE PROCEDURESElectronic Range Control - ERC Models w/One Piece Control TROUBLE SHOOTING GUIDEElectronic Range Control - ERC Models w/One Piece Control TROUBLE SHOOTING GUIDEModels RST359, 361, 362, 365 AUTOMATIC ELECTRONIC TIMERELECTRONIC TIMER Figure 53 - Solid State Digital Timer AUTOMATIC ELECTRONIC TIMEROPERATION AND SERVICE PROCEDURES To Set Alarm Clock FeatureTo Program the Oven for Self-Clean To Program the Oven for Delayed Time BakeModels RST359, 361, 362, 365 TIMER TESTINGOPERATIONAL TEST OPERATION AND SERVICE PROCEDURESModels RST359, 361, 362, 365 OPERATION AND SERVICE PROCEDURESUSING THE MINUTE TIMER OPERATING INSTRUCTIONS FOR COOK AND OFF CLOCK TIMERSETTING THE CLOCK AT POWER-UP SETTING THE CLOCK To Change Current TimeOPERATION AND SERVICE PROCEDURES TO PROGRAM THE OVEN FOR SELF-CLEANCOOK AND OFF TIMER TESTING PROCEDURES TO PROGRAM OVEN FOR TIMED BAKEOPERATION AND SERVICE PROCEDURES BAKE AND BROIL IGNITORSOPERATION AND SERVICE PROCEDURES SELECTOR SWITCHELECTRIC GAS VALVE ELECTRIC GAS VALVE TEST WITH VOLT/OHM METERFigure 67 - Selector Switch Circuit OVEN THERMOSTAT Not Used on Models with ERCOPERATION AND SERVICE PROCEDURES CLOCK TIMER CONTACTS DIAL MECHANICAL TIMER FOR RSS MODELSCLOCK TIMER Non-Solid State TIMER SWITCHMECHANICAL TIMER FOR RSS MODELS OPERATION AND SERVICE PROCEDURESBAKE-ROAST TIMER OPERATION AUTOMATIC ELECTRIC TIMER RSS380AUTOMATICTIC ELECTRONIC TIMER Solid State SELF-CLEAN TIMER OPERATIONOPERATION AND SERVICE PROCEDURES BUZZER ALARMAUTOMATIC ELECTRIC RSS380 DISPLAYFIRE OR EXPLOSION TO AVOID THE RISK OF ELECTRICAL SHOCK PERSONAL INJURY OR DEATH DISCONNECT POWERBEFORE SERVICING, UNLESS TESTING REQUIRES IT LINENEUTRALELECTRIC GAS VALVE TEST WITH VOLT/OHM METER OPERATION AND SERVICE PROCEDURESBAKE AND BROIL IGNITORS ELECTRIC GAS VALVEPERSONAL INJURY OR DEATH DISCONNECT POWER BEFORE SERVICING, UNLESS TESTING REQUIRES IT SELECTOR SWITCHOVEN THERMOSTAT Not Used On Models With ERC OPERATION AND SERVICE PROCEDURESTO CHECK THE MODULE SPARK MODULE TESTINGSPARK SWITCH TEST FIRE OR EXPLOSIONTO TEST THE FLUORESCENT LIGHT SWITCH LATCH SWITCHThe Switch Contacts can be Checked as Follows ROCKER SWITCH TESTINGTO TEST THE BALLAST TOP BURNER VALVETROUBLESHOOTING GUIDE SELF-CLEAN CONTROLS OVEN CONTROLSTROUBLESHOOTING GUIDE BURNER CAPS Models with Sealed Burners INDICATOR LIGHT TESTINGOVEN LIGHT SWITCH TOP BURNERBURNER CAPS Models with Cast Sealed Burners TO CHECK BURNER-BURNER CAPSOPERATION AND SERVICE PROCEDURES Clean burner venturi, or TROUBLE SHOOTING GUIDENOTE If shorting is caus TROUBLESHOOTING GUIDERC231002 Rev TROUBLE SHOOTING GUIDEFIRE OR EXPLOSION Sealed Top BurnersAll Models - Bake, Broil Burner TROUBLESHOOTING GUIDEFIRE OR EXPLOSION Sealed Top BurnersRC231002 Rev TROUBLE SHOOTING GUIDEFIRE OR EXPLOSION All Models - Bake, Broil BurnerRC231002 Rev TROUBLESHOOTING GUIDEFIRE OR EXPLOSION All Models - Bake, Broil BurnerRC231002 Rev TROUBLE SHOOTING GUIDEFIRE OR EXPLOSION All Models - Bake, Broil BurnerOVEN ELECTRIC GAS VALVE DISASSEMBLY PROCEDURES - RST MODELSOVEN BURNER IGNITOR BROIL BURNER IGNITOROVEN BOTTOM USE GLOVE WHEN REMOVING AND INSTALLINGFigure 80 - Oven Light Assembly USE GLOVE WHEN REMOVING AND INSTALLING LAMPOVEN LINER DISASSEMBLY RSS MODELS DISASSEMBLY PROCEDURES - RST MODELSOn models with sealed burners, the burner caps and eight 8 main top mounting screws must be removed. Remove eight 8 burner box mounting screws FLUORESCENT LAMP RST MODELS LIGHT SWITCH - BACKGUARD MOUNTEDCLOCK FLUORESCENT LAMP Backguard RSS MODELSSTARTER SOCKET INDICATOR LIGHT - BACKGUARD MOUNTEDBALLAST RSS MODELS STARTER - FLUORESCENT LIGHTBACKGUARD SUPPORT OVEN LIGHT SWITCH Slide In ModelsINDICATOR LIGHT REMOVEAL OVEN, CLEAN Slide In Models OVEN-ON/CLEAN INDICATOR LIGHTDISASSEMBLY PROCEDURES - RST MODELS TOP BURNER ACTUATOR SWITCHCLOCK DISPLAY BOARD REMOVAL Slide In Models MANIFOLDOVEN THERMOSTAT OVEN LATCH SWITCHTHERMOSTAT, USED IN THE SELF-CLEAN MODELS DOOR LATCH ASSEMBLY RST MODELSMOUNTING BRACKET - TOP BURNER Models without Sealed Burners DOOR LATCH ASSEMBLY RSS MODELSBURNER BOX Models without Sealed Burners TOP BURNERS Models without Sealed BurnersTOP BURNER VENTURI Sealed Burners ELECTRODE WIRE WITH SOCKETTOP BURNER SPARK IGNITORS RSS MODELS BURNER BOX Sealed Burner ModelsOVEN DOOR SPARK MODULE SLIDE - IN MODELSLATCH HANDLE KNOB LATCH HANDLEBOTTOM BRACE CLOCK/TIMER WIRE HARNESS Ribbon Cable RemovalSIDE PANEL REPLACEMENT Models RST307, RST308, RST309DOOR HANDLE - PORCELAIN DOOR Model RST354 OVEN DOOR FRAME - BLACK GLASS DOORBLACK GLASS PANEL OVEN DOOR HANDLE - BLACK GLASS DOORSTORAGE DRAWER HANDLE RST MODELS DOOR GLASS - INNEROVEN DOOR GLASS - PORCELAIN DOOR Model RST354 STORAGE DRAWER PANEL RST MODELSSIDE PANEL TRIM DRAWER ASSEMBLY RST MODELSSTORAGE DRAWER PANEL LINER RST MODELS DRAWER RUNNER RST MODELSPROBLEMS 1. Oven Burner will not turn on OPERATING AND TROUBLESHOOTING PROCEDURES Upper Oven ControlsUPPER OVEN - RST Models Electric Ignitor TestOptional Test with Volt/Ohmmeter Test Procedure Using a Test LampClock Timer Electric Gas ValveOven Light Test ProcedureREPLACEMENT OF PARTS Electric Ignitor DO NOT DROP Upper Oven ThermostatFIRE OR EXPLOSION Upper Oven Clock Timer, Indicator Lights, Control Panel GlassUpper Oven Electric Gas Valve UPPER OVEN - RST ModelsDOOR AND HINGE STRAIGHT UP Upper Oven Door Assemblies RemovalOVEN DOOR HINGE REMOVAL - Top Hinge - Open oven DO NOT ALLOW DOOR TO FALL AND BREAK. LIFTJacket End Light Switch and Fluorescent Light SwitchOven Door Alignment Splash Plate Trim/Splash Plate GlassUPPER OVEN - RST Models UPPER OVEN PARTSRST308 ALTERNATE SPARK MODULE - SEE NEXT PAGE WIRING DIAGRAMS AND SCHEMATICSRC231002 Rev WIRING DIAGRAMS AND SCHEMATICSWIRING DIAGRAMS AND SCHEMATICS RST365 ALTERNATE SPARK MODULE - SEE NEXT PAGERC231002 Rev WIRING DIAGRAMS AND SCHEMATICSWIRING DIAGRAMS AND SCHEMATICS RST378 ALTERNATE SPARK MODULE/ E.R.C. - SEE NEXT PAGERC231002 Rev WIRING DIAGRAMS AND SCHEMATICSWIRING DIAGRAMS AND SCHEMATICS ALTERNATE SPARK MODULE - SEE NEXT PAGERC231002 Rev WIRING DIAGRAMS AND SCHEMATICSWIRING DIAGRAMS AND SCHEMATICS RSS307-OFRC231002 Rev RSS353-OF WIRING DIAGRAMS AND SCHEMATICSRSS343 RC231002 RevWIRING DIAGRAMS AND SCHEMATICS RSS354-OFRC231002 Rev WIRING DIAGRAMS AND SCHEMATICS RSS355 - OFRC231002 Rev WIRING DIAGRAMS AND SCHEMATICS RSS359-OFRC231002 Rev WIRING DIAGRAMS AND SCHEMATICS RSS369-OFRC231002 Rev WIRING DIAGRAMS AND SCHEMATICS RSS380-OFRC231002 Rev RSS358 WIRING DIAGRAMS AND SCHEMATICSRSS356 P1141233, P1141234RC231002 Rev WIRING DIAGRAMS AND SCHEMATICS