Amana RST Clock, FLUORESCENT LAMP Backguard RSS MODELS, Fluorescent Lamp Rst Models, Erc Removal

DISASSEMBLY PROCEDURES - RST MODELS

FIRE OR EXPLOSION - TO AVOID THE RISK OF ELECTRICAL SHOCK, PERSONAL INJURY, OR DEATH, DISCONNECT POWER TO THE OVEN BEFORE SERVICING.

CLOCK

1. Shut off power to range.

2. Remove backguard glass.

3. Remove screws securing clock to the mounting bracket.

4. Pull clock forward and disconnect wiring.

5. When reinstalling clock, refer to the appropriate wiring diagram to assure correct wire termination.

				FLUORESCENT LAMP (Backguard) (RSS MODELS)
		Figure 84		1.	Disconnect electricity at main disconnect plug.
				2. Remove bottom trim and grille supporting glass.
11. Remove rear tank retention clips.					Remove knobs and glass.
				3. Gently twist fluorescent while pulling forward to loosen
12. Grasp the lip of the oven tank and gently maneuver
					end pins in sockets.
		the tank forward to free itself from the range.
				4.	Remove light.
13. Reverse procedure to reinstall hardware.
				5.	Reverse procedure to reinstall light.
14. Reconnect range to electricity and gas. Check main
		gas connection with soap suds.		FLUORESCENT LAMP (RST MODELS)
BACKGUARD GLASS				1.	Disconnect electricity at main disconnect plug.
				2.	Remove backguard glass.
1.		Shut off power to the range.
				3. Fluorescent lamp is now accessible. Twist lamp to
2.		Remove clock or ERC knobs by pulling straight out
					remove from sockets.
		from glass.
3.	Remove two (2) screws securing lower trim		to	LIGHT SWITCH - BACKGUARD MOUNTED
		backguard control panel.
				1.	Disconnect electricity at main disconnect plug.
4.		Tilt glass out at bottom to clear clock or ERC knobs
				2.	Remove backguard glass.
		and light switch stem (if applicable).
				3. Remove fluorescent lamp (if applicable) to prevent
5.		Remove glass and lower trim.
					damage to lamp.
6.	When replacing the glass on models with an oven
				4.	Remove 1/2" nut securing switch to backguard con-
		light and/or fluorescent light, the light switch bezel
					trol panel.
		and retainer clip must be removed from glass and
				5.	Remove four (4) screws (two (2) each side) securing
		transferred to replacement glass.
					backguard control panel to end caps and tilt control
LOWER BACKGUARD TRIM					panel forward.
					NOTE: There is a spacer bracket located between
The lower backguard trim can be replaced by using the
					the control panel and the top trim which will be loose
backguard glass removal procedure.
					when the control panel is moved forward. Replace
When replacing the lower trim, the backguard heat shield
					with angled edge toward back and angle facing
must be removed from trim and attached to replacement
					downward.
trim.
				6. Disconnect wire nuts to switch leads and remove
ERC REMOVAL					switch.
1.		Disconnect electricity at main disconnect plug.		BALLAST - FLUORESCENT LIGHT (RST MODELS)
2.	Remove knobs from ERC by pulling forward on
				1.	Shut off power to the range.
		knobs.
				2.	Remove backguard glass.
3.		Remove backguard glass.
				3. Remove fluorescent lamp to prevent damage.
4.		Remove four (4) screws and spacers securing ERC to
				4.	Remove four (4) screws securing backguard control
		mounting bracket.
					panel to end caps and tilt control panel forward.
5.		Disconnect two (2) wire connectors and remove ERC.
					NOTE: There is a spacer bracket located between
					the control panel and the top trim which will be loose
					when the control panel is moved forward. Replace
					with angled edge toward back and angle facing
					downward.
RC231002 Rev. 3			88