Amana RST, RSS To Set for Self-Clean, To Set for Delayed Self-Clean, To Use Cancel Function

OPERATION AND SERVICE PROCEDURES

Electronic Range Control (ERC) (Models w/Two Piece Control)

"ON" will appear in the display.

To change the broil setting while the oven is operating in the broil mode, simply rotate the "TIME/TEMP SET." knob to change the setting. The ERC will automatically initiate the new broil function approxi- mately two (2) seconds after setting the new entry.

To cancel the broil function, simply press the "SET/ CANCEL" button or rotate the "TIME/TEMP. SET" knob counterclockwise until the three (3) center hori- zontal segments appear on the temperature display. The ERC will then automatically cancel the broil function.

To Set for Self-Clean:

1.Move the door lock lever to the far right or locked position.

2.Press the "CLEAN" button. "CLEAN" will appear along with "3:00" in the display indicating a three (3) hour cleaning time. The ERC will automatically initiate the clean function approximately two (2) sec- onds after the "CLEAN" button is pressed. If the door lock lever is not moved to the locked position prior to pressing the "CLEAN" button, "DOOR" will be dis- played and an alarm will sound as a reminder to lock the door. The "LOCK" light will be displayed approxi- mately ten (10) to twenty (20) minutes into the clean cycle and remain on after the completion of the clean cycle. At the completion of the clean cycle the time of day will be displayed along with the "LOCK" light. The "LOCK" light will turn off when the oven tempera- ture is at a safe level to open the door.

3.Allow the oven to cool approximately twenty (20) to thirty (30) minutes before trying to move the door lock lever to the open position. DO NOT FORCE THE LOCK LEVER. If the door lock will not open, wait five

(5) minutes and try again. NOTE: The "LOCK" light and actual door latch locking/unlocking temperatures are not calibrated with each other, i.e., the door lock may be opened before the "LOCK" light turns off or vice versa.

To Set for Delayed Self-Clean:

1.Move the door lock lever to the far right or locked position.

2.Press the "STOP TIME" button. "STOP TIME" and the current time of day will be displayed.

3.Rotate the "TIME/TEMP. SET" knob clockwise to set the desired time the oven is to turn off.

4.Press the "CLEAN" button. "DELAY", "CLEAN", and

"TIME" will appear along with "3:00" in the display indicating a three (3) hour cleaning time. If the door lock lever is not moved to the lock position prior to pressing the "CLEAN" button. "DOOR" will be dis- played and an alarm will sound as a reminder to lock the door. The ERC will automatically calculate the start time.

EXAMPLE: If the current time of day is 12:00, to operate the oven in a clean function which will end at 5:00, (1) lock the oven door, (2) set the stop time for 5:00 and, (3) press the "CLEAN" button. The ERC will start the cleaning function at 2:00 and turn the oven off at 5:00.

When the start time is reached, "DELAY" will turn off, "ON" will appear, and the ERC will initiate the clean cycle. The "LOCK" indicator will be displayed ap- proximately 10-20 minutes into the clean cycle and remain on after the completion of the clean cycle. When the stop time is reached, the ERC will auto- matically turn the oven off and the time of day and "LOCK" will be displayed. "LOCK" will remain dis- played until the oven temperature is at a safe level to open the door.

5.Allow the oven to cool approximately twenty (20) to thirty (30) minutes before trying to move the door lock lever to open the door. DO NOT FORCE THE LOCK LEVER. If the door lock will not open, wait five (5) minutes and try again. NOTE: The "LOCK" light and actual door latch locking/unlocking temperatures are not calibrated with each other, i.e., the door lock may be opened before the "LOCK" light turns off or vice versa.

To Use Cancel Function:

1.Pressing the "SET/CANCEL" button will cancel all cooking, cleaning, or timing functions except the minute timer function. The display will return to the time of day unless a minute timer operation is present.

2.To display the time of day during a program, press the "CLOCK" button. The display will return to the time of day. To view the remaining time on a program after returning the display to the time of day, simply press the appropriate function button ("MINUTE TIMER", "STOP TIME", "COOK TIME", or "CLEAN" button). The display will then show the remaining program time.

ELECTRONIC RANGE CONTROL - ERC

RC231002 Rev. 3 34