Cx show all, 3JV3MVTA | AMCC 9500S, 9550SX, 9590SE, 9650SE manual

Controller Object Commands

/cx show all

This command shows the current setting of all of the following attributes on the specified controller: driver, model, memory, firmware, bios, monitor, serial, pcb, pchip, achip, numports, numunits, numdrives, unitstatus, drivestatus, allunitstatus, exportjbod, ondegrade, spinup, stagger and autocarve.

Example: (where x represents the actual version number)

//localhost> /c0 show all
/c0 Driver Version = 3.x
/c0 Model = 9550SX-12	112MB
/c0 Memory Installed =	112MB
/c0 Firmware Version = FE9X 3.x
/c0 Bios Version = BE9X	3.x
/c0 Monitor Version = BL9X 3.x
/c0 Serial Number = xxxxx
/c0 PCB Version = Rev 0xx
/c0 PCHIP Version = 1.xx
/c0 ACHIP Version = 3.xx
/c0 Number of Ports = 12
/c0 Number of Units = 2
/c0 Number of Drives = 12
/c0 Total Optimal Units	= 2
/c0 NotOptimalUnits = 0
/c0 Total Units = 2
/c0 JBOD Export Policy = off
/c0 Disk Spinup Policy = 7
/c0 Spinup Stagger Time	Policy (sec) = 4
/c0 Cache on Degrade Policy = Follow Unit Policy
/c0 Auto-Carving Policy	= off
/c0 Auto-Carving Size =	2047 GB
/c0 Auto-Rebuild Policy	= enable
Unit UnitType Status	%RCmpl %V/I/M Stripe Size(GB) Cache AVerify

--------------------------------------------------------------------------

u0	RAID-5	OK	-		-		256K	148.99	ON	ON
u1	RAID-5	OK	-		-		256K	595.961	ON	OFF
Port	Status		Unit	Size			Blocks		Serial
---------------------------------------------------------------
p0	OK		u0	74.53	GB		156301488		3JV3MV1C
p1	OK		u0	74.53	GB		156301488		3JV3MK6B
p2	OK		u0	74.53	GB		156301488		3JV3LW52
p3	OK		u1	74.53	GB		156301488		3JV49S77
p4	OK		u1	74.53	GB		156301488		3JV3MVTA
p5	OK		u1	74.53	GB		156301488		5JV980Z0
p6	OK		u1	74.53	GB		156301488		5JV9820G
p7	OK		u1	111.79		GB	234441648		WD-WMAEL10275
p8	OK		u1	111.79		GB	234441648		WD-WMAEL10274
p9	OK		u1	111.79		GB	234441648		WD-WMAEL10281
p10	OK		u1	111.79		GB	234441648		WD-WMAEL10273
p11	OK		u1	111.79		GB	234441648		WD-WMAEL10274
Name	OnlineState		BBUReady Status			Volt		Temp	Hours	LastCapTest

---------------------------------------------------------------------------

bbu On

Yes

OK

OK

OK

165

06-Nov-2004

www.3ware.com

39

Image 45

AMCC 9500S, 9550SX, 9590SE, 9650SE manual Cx show all, 3JV3MVTA

Contents

3ware Serial ATA RAID Controller Command Line Interface Copyright Table of Contents 3ware Serial ATA RAID Controller CLI Guide Cx/ux set autoverify=onoff 3ware Serial ATA RAID Controller CLI Guide About this CLI Guide Features of the CLI Introduction to the 3ware Command Line Interface Terminology Supported Operating Systems Installing the 3ware CLI on Windows Installing the 3ware CLITo install 3ware CLI on Windows Permissions Required to Run CLI To start CLI, do one of the following Installing the 3ware CLI on Linux and FreeBSD Using the command interface interactively Working with 3ware CLITo use the CLI interactively Using a single command with output Using an input file to execute a scriptScripting example Conventions Outputting the CLI to a Text File RAID Concepts Understanding RAID Levels and Concepts RAID Available RAID Configurations RAID 1 Configuration Example RAID 5 Configuration Example RAID 6 Configuration Example RAID 10 Configuration Example Jbod Single Disk Possible Configurations Based on Number of Drives RAID Configuration TypesDetermining What RAID Level to Use Hot Spare Drive Capacity Using Drive Capacity Efficiently Support for Over 2 Terabytes CLI Syntax Reference Common Tasks Mapped to CLI Commands CLI Syntax Reference Port Tasks Syntax Overview C1 add type=raid1 disk=0-1 Focus Object Shell Object Commands Example Show Show ver Show alarms reverse Show diagShow rebuild Show selftest Show verify Flush RescanCommit Cx show Controller Object Commands Cx show Cx show attribute attribute Cx show driver Cx show biosCx show model Cx show firmware Cx show pcb Cx show serialCx show pchip Cx show achip Cx show numunits Cx show numportsCx show ctlbus Cx show exportjbod Cx show stagger Cx show spinupCx show ondegrade Cx show autocarve Cx show memory Cx show carvesize Cx show unitstatus Cx show autorebuild Cx show drivestatus Cx show allunitstatus 3JV3MVTA Cx show all Supported RAID Types Supported Stripe Sizes KB Supported Model-Unit Types for ignoreECC Cx rescan noscan Cx flush Cx commit Cx show alarms reverse Cx show rebuild Cx show diag RAID-5 Initializing Cx show verify Cx show selftest Cx add rebuild=dddhhduration Setting Up a Rebuild Schedule Cx add verify=dddhhduration Setting Up a Verify Schedule Cx add selftest=dddhh Setting Up a Selftest Schedule Cx del rebuild=slotid Cx set rebuild=enabledisable1..5Cx del verify=slotid Cx del selftest=slotid Cx set selftest=enabledisable task=UDMASMART Cx set verify=enabledisable1..5 Cx set exportjbod=onoff Cx set ondegrade=cacheofffollowCx set spinup=nn Cx set stagger=nn Cx set autocarve=onoffCx set carvesize=1024..2048 Cx set autodetect=onoff disk=p-pall Cx set autorebuild=onoff Cx start mediascan Cx stop mediascan Unit Object Commands Cx/ux show Cx/ux show status Cx/ux show rebuildstatusCx/ux show verifystatus Cx/ux show name Cx/ux show initializestatusCx/ux show serial Cx/ux show qpolicy Cx/ux show identify Cx/ux show storsaveCx/ux show autoverify Cx/ux show cache Cx/ux show volumes Cx/ux show ignoreECCCx/ux show all Cx/ux remove noscan quiet Cx/ux start rebuild disk=pp-p...ignoreECC Cx/ux del noscan quiet Cx/ux pause rebuild Cx/ux start verifyCx/ux resume rebuild Supported RAID Logical Unit Types for Verification Cx/ux flush Cx/ux stop verifyCx/ux set autoverify=onoff Cx/ux set cache=onoff quiet Cx/ux set identify=onoff Cx/ux set ignoreECC=onoffSupported RAID Types for Caching Cx/ux set name=string Cx/ux set qpolicy=onoffCx/ux set storsave=protectbalanceperform quiet Example 3ware Serial ATA RAID Controller CLI Guide Valid Migration Paths Supported Stripe Sizes Migration Process Example of splitting a mirrorExample of capacity expansion Example of migrate output Cx/px show Port Object Commands Cx/px show model Cx/px show statusCx/px show serial Cx/px show firmware Cx/px show lspeed Cx/px show ncqCx/px show capacity Cx/px show smart Cx/px show all Cx/px set identify=onoff Cx/px remove noscan quiet Cx/bbu show BBU Object Commands Cx/bbu show status Cx/bbu show attribute attribute Cx/bbu show lasttest Cx/bbu show batinstCx/bbu show volt Cx/bbu show temp Cx/bbu show serial Cx/bbu show bootloaderCx/bbu show fw Cx/bbu show pcb Cx/bbu enable Cx/bbu disable quietCx/bbu test quiet Ex show Enclosure Object Commands Ex show controllers Ex show attribute attribute Ex show fans Ex show slotsEx show temp Ex show all Ex/slotx show Ex/slotx show identifyEx/slotx set identify=onoff Help with specific commands Help CommandsEx/fanx show Ex/tempx show Attribute attribute Help Help with attributes Help show Help updateHelp flush Help rescan Help /cx Help focusHelp /cx/ux Help /cx/px Return Code Command LoggingHelp /ex/fanx Help /ex/tempx If you type