Manuals / AMX / Computer Equipment / Network Card

AMX NI-2000 NI-4000 Specifications Cont, Introduction, Included Accessories, Optional Accessories

Models: NI-2000 NI-4000 NI-3000

1 134

Download 134 pages 57.78 Kb

Page 20

Manual background

Introduction

NI-4000 Specifications (Cont.)

CardFrame Number	• Sets the starting address for the Control Cards in the CardFrame.(Factory
DIP switch	default CardFrame DIP switch value = 0).
	• The Control Card address range is 1-3064.
NetLinx Control Card	• Four 20-pin (male) connectors that bridge the gap between the Control
connectors (1-4)	Cards in the CardFrame and external equipment.

Included Accessories:	• Two CC-NIRC IR Emitters (FG10-000-11)
	• One 10-pin 3.5 mm mini-Phoenix (female) I/O connector (41-5107)
	• Two 8-pin 3.5 mm mini-Phoenix (female) Relay connector (41-5083)
	• One 4-pin 3.5 mm mini-Phoenix (female) AXlink connector (41-5047)
	• One 2-pin 3.5 mm mini-Phoenix (female) PWR connector (41-5025)
	• Installation Kit (KA2105-01):
	One 8-pin Relay Common Strip (41-2105-01)
	Four rack mount screws (80-0186)
	Four washers (80-0342)
	• Removable rack ears. Allows for tabletop, under-counter, and
	front/rear rack mounting

Optional Accessories:	• 2 Pin Black Male Phoenix Connector (3.5mm) (41-5026)
	• CC-NIRC IR cables (FG10-000-11)
	• CC-NSER IR/Serial cables (FG10-007-10)
	• CSB Cable Support Bracket (FG517)
	• NCK, NetLinx Connector Kit (FG2902)
	• NI-4000 Quick Start Guide (93-2105-01)
	• PSN2.8 12 VDC power supply (FG423-17)
	• PSN6.5 12 VDC power supply (FG423-41)
	• STS, Serial To Screw Terminal (FG959)
	• Upgrade Compact Flash (factory programmed with firmware):
	NXA-CFNI64M- 64 MB compact flash card (FG2116-31)
	NXA-CFNI128M- 128 MB compact flash card (FG2116-32)
	NXA-CFNI256M- 256 MB compact flash card (FG2116-33)
	NXA-CFNI512M- 512 MB compact flash card (FG2116-34)
	NXA-CFNI1G- 1 GB compact flash card (FG2116-35)
	• NXC cards (see the Card Slot section (page 12) of this Specification table
	for more detailed information)

	14	NetLinx Integrated Controllers

Image 20

AMX NI-2000, NI-3000 NI-4000 Specifications Cont, Introduction, Included Accessories, Optional Accessories

Contents

NetLinx Integrated Controllers instruction manualNI-2000, NI-3000, and NI-4000 NetLinx Central Controllers and CardsAMX Limited Warranty and Disclaimer Table of Contents Quick Setup and Configuration OverviewConnections and Wiring IntroductionNetLinx Security and Web Server Installation and UpgradingConfiguration and Firmware Update NetLinx Security with a Terminal Connection Troubleshooting ProgrammingNetLinx Integrated Master Controller Features NI-2000 SpecificationsIntroduction NI-2000 Specifications Dimensions HWDWeight IntroductionNI-2000 Specifications Cont Front Panel ComponentsRear Panel Components NetLinx Integrated ControllersThe D notation is used to explicitly represent a device number NI-2000 Specifications ContIntroduction NI-3000 Specifications NI-2000 Specifications ContIncluded Accessories Optional Accessoriesswitch IntroductionFront RearNI-3000 Specifications Cont Dimensions HWDPower requirements WeightRear Panel Components NI-3000 Specifications ContIntroduction NI-3000 Specifications Cont Included AccessoriesIntroduction The D notation is used to explicitly represent a device numberNI-4000 Specifications NI-3000 Specifications ContNI-4000 Specifications Dimensions HWDPower requirements WeightRear Panel Components NI-4000 Specifications ContIntroduction NI-4000 Specifications Cont IntroductionThe D notation is used to explicitly represent a device number NetLinx Integrated ControllersNI-4000 Specifications Cont Included AccessoriesOptional Accessories IntroductionConfiguration and Communication Quick Setup and Configuration OverviewInstallation Procedures Update the Controller and Control Card Firmware Program NetLinx Security into the On-Board MasterStudio to the most recent release IP recommendedConnections and Wiring Setting the Configuration DIP Switch for the Program PortBaud rate settings Baud Rate Settings on the Configuration DIP SwitchWiring Guidelines Modes and Front Panel LED Blink PatternsUsing the Configuration DIP switch Modes and LED Blink PatternsPreparing captive wires Wiring length guidelinesWiring Guidelines - NI-4000 & NI-3000@ 900 mA Wiring Guidelines - NI-2000 @ 700 mAUsing the 4-pin mini-Phoenix connector for data and power Using the 4-pin mini-Phoenix connector for data with external powerProgram Port, Pinouts, and Signals Program Port Connections and WiringRS-232/422/485 Device Port Wiring Specifications ICSNet RJ-45 Connections/Wiring RS-232/422/485 Device Port Wiring SpecificationsICSNet RJ-45 Signals Connections and WiringEthernet 10/100 Base-T RJ-45 Connections/Wiring ICSHub OUT Pinouts and SignalsEthernet RJ-45 Pinouts and Signals ICSHub OUT portRelay Connections and Wiring Ethernet LEDsEthernet ports used by the Integrated Controllers Ethernet Ports Used by the NetLinx Integrated ControllersInput/Output I/O Connections and Wiring Relay connectionsIR/Serial Connections and Wiring I/O Port Wiring Specifications NI-4000 and NI-3000I/O Port Wiring Specifications NI-2000 IR/Serial Connector Wiring SpecificationsNetLinx Control Card Slot Connector NI-4000 unit only Connections and WiringFIG. 17 NetLinx Control Card 20-pin connector NetLinx Integrated ControllersConnections and Wiring NetLinx Integrated ControllersInstallation and Upgrading Installing NetLinx Control Cards NI-4000 OnlySetting the NetLinx Control Card Addresses NI-4000 Only DevicePortSystem DPSCompact Flash Upgrades Removing NetLinx Control Cards NI-4000 OnlyOptional Compact Flash Upgrades Accessing the internal components on an Integrated ControllerInstallation of Compact Flash upgrades Closing and Securing the Integrated Controller FIG. 22 Mounting Integrated Controller into an equipment rack Installing the Integrated Controller into an Equipment RackInstall screws Bracket Rack Mounting Holes 10. Apply power to the unit by using an active PSN power supply Installation and Upgrading NetLinx Integrated ControllersBefore beginning Configuration and Firmware UpdateCommunicating with the Master via the Program Port Setting the System Value Select Diagnostics Device Addressing from the Main menuUsing multiple NetLinx Masters there is a problem, use a system value of zero 0 on the Master Changing the Device Address on a NetLinx DeviceSelect Diagnostics Device Addressing from the Main menu Recommended NetLinx Device numbers Resetting the Factory Default System and Device ValuesSelect Diagnostics Device Addressing from the Main menu Obtaining the Master’s IP Address using DHCP Assigning a Static IP to the NetLinx Master 1. Select Diagnostics Network Addresses from the Main menuCommunicating with the On-board Master via an IP FIG. 28 Assigning Communication Settings and TCP/IP Settings Verifying the current version of NetLinx Master Firmware Upgrading the On-board Master Firmware via an IP6. Select the NI Master’s KIT file from the Files section FIG Upgrading the NI Controller Firmware via an IP FIG. 31 Assigning Communication Settings and TCP/IP SettingsNetLinx Integrated Controllers Configuration and Firmware UpdateUpgrading the new NI Controller firmware via an IP 6. Enter the Device number of the target NetLinx Integrated Controller Upgrading the Control Card Firmware via an IP 13. Right-click the associated System number and select Refresh System. This establishes a new connection to the specified System and populates the list with devices on that system. The communication method is then highlighted in green on the bottom of the NetLinx Studio window Supported Browser and Feature Compatibility NetLinx Security and Web ServerNetLinx Security web browser and feature support New Master Firmware Security Features NetLinx Security TermsMaster Security Telnet Security Terminal RS232 Program port security HTTP Web Server Security FTP SecurityNetLinx Security Terms Cont Accessing the NetLinx Master via its IP AddressWebControl Tab Default Security Configuration WebControl Tab FeaturesDefault Security Configuration Security Options FTP Security - EnabledSecurity link is selected Security TabSecurity Tab Features Security Tab Features Cont Security tab - Enable Security pageSecurity System Features FeatureAdd Group Entries Security System Features ContSecurity tab - Add Group page Modify Group Entries Add Group Entries ContSecurity tab - Modify Group page Modify Group Entries Cont Security tab - Group Directory Associations pageFeature Valid Directory Association EntriesGroup Directory Association Entries NetLinx Security and Web ServerFeature Security tab - Add User pageAdd User Entries NetLinx Security and Web ServerSecurity tab - Modify User page Modify User EntriesModify User Entries Cont Security tab - User Directory Associations pageValid Directory Association Entries User Directory Association EntriesSecurity tab - SSL Server Certificate page Server Certificate EntriesServer Certificate Entries Cont certificate because the Master Key has been changedSecurity tab - Export Certificate Request page Security tab - Import Certificate pageFIG. 44 Security Tab - Export Certificate Request field FIG. 45 Security Tab - Import Certificate fieldNetwork Tab System TabShow Devices Tab Master Security Setup Procedures FIG. 48 Security tab - showing NetLinx Master security optionsAdding a Group and assigning their access rights The administrator group account cannot be deleted or modifiedModifying an existing Group’s access rights FIG. 50 Security tab - showing the Modify Group access rights fieldsShowing a list of authorized Groups Deleting an existing GroupAdding a Group directory association Valid Directory Association EntriesThe administrator user account cannot be deleted or modified Confirming the new directory association2. Click the Directory Associations link Deleting a directory associationAdding a User and configuring their access rights NetLinx cannot be used since they already existModifying an existing User’s access rights Showing a list of authorized Users Deleting a UserAdding a User directory association SSL Certificate Procedures Confirming the new directory association2. Click the Directory Associations link Deleting a directory associationSelf-Generating a SSL Server Certificate Request This domain name does not need to be a resolvable URL Address whenself-generating a certificate The city/province name must be fully spelled outCreating a Request for a SSL Server Certificate The state/province name must be fully spelled outImporting a CA certificate to the Master over a secure SSL connection Before importing a CA server certificate, you mustDisplay SSL Server Certificate Information Regenerating an SSL Server Certificate RequestCommon Steps for Requesting a Certificate from a CA 7. Before exiting the Master and beginning another session4. Enter the name of the server being used this is the Master Accessing an SSL-Enabled Master via an IP Address 7. Click Next to proceed with the certificate storage process Using your NetLinx Master to control the G4 panel Using your NetLinx Master to control the G3 panel FIG. 60 WebControl VNC installation and Password entry screensWhat to do when a Certificate Expires a new certificate from your current CANetLinx Security Features Initial Setup via a Terminal ConnectionNetLinx Security with a Terminal Connection NetLinx Security FeaturesAccessing the Security configuration options If NetLinx Master security is not enabled, you will see the following Option 3 - Add user Security Options MenuOption 2 - Display system security options for NetLinx Master Option 4 - Edit User Edit User MenuAccess Rights Menu CommandEdit User Menu NetLinx Security with a Terminal ConnectionAccess Rights Menu Option 5 - Delete userOption 6 - Show the list of authorized users Option 7 - Add GroupEdit Group Menu Edit Group Menu Add directory associationEdit Group menu List directory associations Edit Group menu Change Access RightsEdit Group menu Delete directory association Option 9 - Delete Group Edit Group menu Display Access RightsOption 8 - Edit Group Option 11 - Set Telnet Timeout in seconds Option 12 - Display Telnet Timeout in secondsOption 10 - Show List of Authorized Groups Option 13 - Make changes permanent by saving to flashMain Security Menu CommandMain Security Menu NetLinx Security with a Terminal ConnectionDescription Default Security ConfigurationMain Security Menu Cont Command Help menuHelp Menu Options NetLinx Security with a Terminal ConnectionLogging Into a Session Help Menu Options ContHelp Security LogoutSetup Security Using the ID Button ProgrammingConverting Axcess Code to NetLinx Code DevicePortSystem DPSProgram Port Commands Program Port CommandsPC COM Port Communication Settings Program Port Commands Cont Program Port Commands Cont SET IP DPSESC Pass Codes Notes on Specific Telnet/Terminal ClientsEscape Pass Codes WindowsTM client programsLED Disable/Enable SendCommands RS-232/422/485 SendCommandsRS232/422/485 Ports Channels LED SendCommandsRS-232/422/485 SendCommands Cont RS-232/422/485 SendCommands Cont HSONRXCLR RXOFFRS-232/422/485 SendString Escape Sequences RS-232/422/485 SendString Escape SequencesRS-232/422/485 SendCommands Cont IR/Serial SendCommands IR / Serial Ports ChannelsIR RX Port Channels IR/Serial SendCommandsIR/Serial SendCommands Cont ProgrammingCTOF CTONIR/Serial SendCommands Cont SENDCOMMAND DEV, GET MODEIR/Serial SendCommands Cont Sets the time between power SENDCOMMAND DEV, PTOF,TimeIR/Serial SendCommands Cont Input/Output SendCommands I/O SENDCOMMANDSProgramming GET INPUTProgramming NetLinx Integrated ControllersTroubleshooting Troubleshooting InformationTroubleshooting SymptomTroubleshooting Information Cont TroubleshootingSymptom SolutionTroubleshooting Information Cont SymptomSolution During the firmware upgradeRevisionLast12/10/04