NI-2000 Specifications | AMX NI-4000, NI-3000 specification

Introduction

Introduction

NetLinx Integrated Master Controllers can be programmed to control RS-232/422/485, Relay, IR/ Serial, and Input/Output devices through the use of both the NetLinx programming language and the NetLinx Studio application (version 2.2 or higher). Another key feature of this products is the ability to easily access the configuration switches without having to remove a

cover plate.

NetLinx Integrated Master Controller Features

NI-2000	• 1 RS-232 Program port
(FG2105-01)	• 3 RS-232/RS-422/RS-485 ports

	• 4 IR/Serial Output ports
	• 4 Digital Input/Output ports
	• 4 Relays

NI-3000	• 1 RS-232 Program port
(FG2105-02)	• 7 RS-232/RS-422/RS-485 ports

	• 8 IR/Serial Output ports
	• 8 Digital Input/Output ports
	• 8 Relays

NI-4000	• Support for up to 4 NetLinx control cards (such as NXC-COM2,NXC-IRS4, etc.)
(FG2105)	• 1 RS-232 Program port

	• 7	RS-232/RS-422/RS-485 ports
	• 8	IR/Serial Output ports
	• 8	Digital Input/Output ports
	• 8	Relays

The NI series of controllers use a combination lithium battery and clock crystal package called a Timekeeper. Only one Timekeeper unit is installed within a given NI controller. The battery can be expected to have up to 3 years of usable life under very adverse conditions. Actual life is appreciably longer under normal operating conditions. This calculation is based on storing the unit without power in 50° C (120° F) temperature until battery levels are no longer acceptable. The part number for a replacement battery is 57-0032.

NI-2000 Specifications

The front panel LEDs (FIG. 1) are grouped by control type and are numbered according to their corresponding port (connector) numbers on the rear of the unit. The back of the unit contains three RS-232/422/485, one Relay, one IR/Serial and one I/O connectors. In addition, this unit provides an ID pushbutton, AXlink LED, and other related connectors. FIG. 2 shows the front and rear of the NI-2000.

NetLinx Integrated Controllers	1

Image 7

AMX NI-4000, NI-3000 instruction manual NI-2000 Specifications, NetLinx Integrated Master Controller Features

Contents

NetLinx Integrated Controllers AMX Limited Warranty and Disclaimer Table of Contents Installation and Upgrading NetLinx Security with a Terminal Connection Troubleshooting 125 NetLinx Integrated Master Controller Features NI-2000 Specifications NI-2000 Specifications Rear Panel Components Front Panel Components D notation is used to explicitly represent a device number Included Accessories NI-3000 SpecificationsOptional Accessories Green ICSNet AXLink LED RS-232/422/485 Ports ICSHub OutRelays IR/Serial Ports Ethernet AXLink Program Power requirements NI-3000 SpecificationsCompact Flash Rear Panel Components Two 8-pin 3.5 mm mini-Phoenix female Relay connector Whether to use half duplex or full duplex modeTurns Off when the speed is 10 Mbps One 10-pin 3.5 mm mini-Phoenix female I/O connector NI-4000 NetLinx Integrated Controller front view NI-4000 Specifications NI-4000 Specifications Rear Panel Components D notation is used to explicitly represent a device number Front/rear rack mounting Pin Black Male Phoenix Connector 3.5mmTwo CC-NIRC IR Emitters FG10-000-11 Removable rack ears. Allows for tabletop, under-counter, Configuration and Communication Installation Procedures IP recommended Update the Controller and Control Card FirmwareProgram NetLinx Security into the On-Board Master Studio to the most recent release Program Run Disable PRD mode Setting the Configuration DIP Switch for the Program PortBaud rate settings Baud Rate Settings on the Configuration DIP Switch Modes and LED Blink Patterns Wiring GuidelinesUsing the Configuration DIP switch Modes and Front Panel LED Blink Patterns Wiring Guidelines NI-2000 @ 700 mA Preparing captive wiresWiring length guidelines Wiring Guidelines NI-4000 & NI-3000@ 900 mA Local +12 VDC power supply coming from the PSN power supply Using the 4-pin mini-Phoenix connector for data and powerAXlink/PWR connector AXlink/PWR connector PWR + GND Top view RS-232/422/485 Device Port Wiring Specifications Program Port Connections and WiringProgram Port, Pinouts, and Signals RJ-45 Pinout Information EIA/TIA 568 B ICSNet RJ-45 Connections/WiringRS-232/422/485 Device Port Wiring Specifications ICSNet RJ-45 Signals ICSHub OUT port Ethernet 10/100 Base-T RJ-45 Connections/WiringICSHub OUT Pinouts and Signals Ethernet RJ-45 Pinouts and Signals Ethernet Ports Used by the NetLinx Integrated Controllers Relay Connections and WiringEthernet LEDs Ethernet ports used by the Integrated Controllers Relay connections Input/Output I/O Connections and Wiring IR/Serial Connector Wiring Specifications IR/Serial Connections and WiringPort Wiring Specifications NI-4000 and NI-3000 Port Wiring Specifications NI-2000 NetLinx Control Card 20-pin connector NetLinx Control Card Slot Connector NI-4000 unit only Connections and Wiring Thumbscrews NXC Card Slot faceplate Installing NetLinx Control Cards NI-4000 OnlyCard slots Sample NXC cards Internal Guide slots 192 384 768 1536 Setting the NetLinx Control Card Addresses NI-4000 OnlyDevicePortSystem DPS Structure DEV Removing NetLinx Control Cards NI-4000 Only Compact Flash UpgradesOptional Compact Flash Upgrades Carefully Detach ALL Connectors from the rear of the unit Installation of Compact Flash upgrades Removing the Compact Flash card Closing and Securing the Integrated Controller Install screws Bracket Rack Mounting Holes Installing the Integrated Controller into an Equipment Rack Installation and Upgrading Installation and Upgrading Before beginning Communicating with the Master via the Program Port Select Diagnostics Device Addressing from the Main menu Setting the System ValueDefault setting for these units is Using multiple NetLinx Masters Device Addressing dialog changing the device value Changing the Device Address on a NetLinx Device Recommended NetLinx Device numbers Resetting the Factory Default System and Device ValuesAxcess Devices use Axcess standards Used to assign an IP Address Used to obtain an Obtaining the Master’s IP Address using Dhcp Assigning a Static IP to the NetLinx Master Select Diagnostics Network Addresses from the Main menuUsed to assign an IP Address Communicating with the On-board Master via an IP Assigning Communication Settings and TCP/IP Settings Upgrading the On-board Master Firmware via an IP Verifying the current version of NetLinx Master Firmware Firmware download status Selected on-board Master Firmware fileDevice and System Number Upgrading the NI Controller Firmware via an IP Sample NetLinx Workspace window Upgrading the new NI Controller firmware via an IP Firmware file NIX000 Firmware download status Selected Integrated Controller Upgrading the Control Card Firmware via an IP Firmware file Firmware download status Selected Control Card Safari Yes NetLinx Security web browser and feature supportSupported Browser and Feature Compatibility OS Platform NetLinx Security Terms New Master Firmware Security FeaturesNetLinx Security Terms WebControl Tab Accessing the NetLinx Master via its IP Address WebControl Tab Features Default Security ConfigurationDefault Security Configuration Groups section Security Tab FeaturesFeature Description System section Security Tab Security System Features Security tab Enable Security Add Group Entries Administrator’s user passwordsDefault password can no longer be used to gain access Security tab Add Group Modify Group Entries Security tab Modify Group Security tab Group Directory Associations Group Directory Association Entries Valid Directory Association EntriesPath Description Sensitive and must be unique Security Config AccessSecurity tab Add User Add User Entries Modify User Entries Security tab Modify User Must be unique Security tab User Directory Associations New user is selected Enables access to the user directory and all filesUser Directory Association Entries Subdirectories in that user directory Server Certificate Entries Security tab SSL Server CertificateCommon Name can not be an IP Address Previous fields and generates its own SSL Certificate Information from the certificate currently installed onIs an alpha-numeric string 1 50 characters in length Create Request Takes the information entered into Security tab Import Certificate Security tab Export Certificate Request Show Devices Tab System TabNetwork Tab Security tab showing NetLinx Master security options Master Security Setup Procedures Security tab showing the Add Group fields Adding a Group and assigning their access rights Security tab showing the Modify Group access rights fields Modifying an existing Group’s access rights Deleting an existing Group Showing a list of authorized Groups Security tab showing the Group Directory Associations fields Adding a Group directory association Click the Directory Associations link Confirming the new directory associationDeleting a directory association NetLinx cannot be used since they already exist Adding a User and configuring their access rights Security tab showing the Modify User Configurations fields Modifying an existing User’s access rights Deleting a User Showing a list of authorized Users Security tab showing the User Directory Associations fields Adding a User directory association SSL Certificate Procedures City/province name must be fully spelled out Self-Generating a SSL Server Certificate Request State/province name must be fully spelled out Creating a Request for a SSL Server Certificate YOU can not Request Another Certificate Until the Previous Before importing a CA server certificate, you must Regenerating an SSL Server Certificate Request Display SSL Server Certificate Information Before exiting the Master and beginning another session Common Steps for Requesting a Certificate from a CA NetLinx Security and Web Server Security Alert and Certificate popups Accessing an SSL-Enabled Master via an IP Address Click Next to proceed with the certificate storage process G3 panel G4 panel Using your NetLinx Master to control the G4 panel WebControl VNC installation and Password entry screens Using your NetLinx Master to control the G3 panel What to do when a Certificate Expires Establishing a Terminal connection NetLinx Security FeaturesInitial Setup via a Terminal Connection NetLinx Security Features Stop bits1, and Flow control None default is Hardware Accessing the Security configuration options Terminal Option 3 Add user Command DescriptionSecurity Options Menu Option 2 Display system security options for NetLinx Master Edit User Menu Option 4 Edit User Edit User Menu Option 7 Add Group Access Rights MenuOption 5 Delete user Option 6 Show the list of authorized users Subdirectories in the user directory PathGranted to that file Edit Group menu Delete directory association Option 9 Delete Group Option 8 Edit Group Option 13 Make changes permanent by saving to flash Option 11 Set Telnet Timeout in secondsOption 12 Display Telnet Timeout in seconds Option 10 Show List of Authorized Groups Main Security Menu Main Security Menu Command Help Menu Options Help menu Logging Into a Session Logout Setup SecurityHelp Security Converting Axcess Code to NetLinx Code Using the ID ButtonDevicePortSystem DPS PC COM Port Communication Settings Program Port CommandsProgram Port Commands MEM Reboot DPSSendcommand GET IP DPS Show Device DPS SET IP DPSSET Time SET URL DPS + + ESC ESC ESC Pass CodesEscape Pass Codes WindowsTM client programs Linux Telnet client LED Disable/Enable SendCommandsRS-232/422/485 SendCommands RS232/422/485 Ports Channels Sendcommand RS2321,CHARDM10 Sendcommand DEV,B9MONSendcommand RS2321,B9MON Sendcommand RS2321,CHARD10 Sendcommand RS2321,RXCLR Sendcommand DEV,HSONSendcommand RS2321,HSON Sendcommand DEV,RXCLR RS-232/422/485 SendString Escape Sequences RS-232/422/485 SendString Escape Sequences IR RX Port Channels IR/Serial SendCommandsIR/Serial SendCommands IR / Serial Ports Channels Sendcommand IR1,CTON,20 Sendcommand IR1, CH,18Sendcommand IR1,CP,2 Sendcommand IR1,CTOF,10 Sendcommand IR1,IROFF Sendcommand DEV, GET ModeSendcommand IR1,GET Mode Sendcommand DEV,IROFF Sendcommand IR1, SET Mode IR Sendcommand IR1, PTOF,15Sendcommand IR1, PTON,15 Sendcommand IR1, SET IO Link Sendcommand IR1, XCH Sendcommand IR1,XCHM Sendcommand IO,SET Input 1 High Input/Output SendCommandsSendcommand DEV,GET Input Chan Sendcommand IO,GET Input Programming 124 Troubleshooting Information SET Ethernet Mode 100 Full SET Ethernet Mode 10 HalfSET Ethernet Mode 10 Full SET Ethernet Mode 100 Half Process, NetLinx Studio failed to Symptom Solution During the firmware upgradeInstall the last component IP section on page 46 for detailed procedures RevisionLast12/10/04