Manuals / Baldor / Household Appliance / Home Security System

Baldor BXII installation manual Power on checks, 5-2Operation, MN1904

Models: BXII

1 88

Download 88 pages 52.21 Kb

Page 42

5.1.5 Power on checks

5.1.5 Power on checks

If at any time one of the Axis LEDs is illuminated red, this indicates that the NextMove BXII has detected a fault - see section 6.

1.Turn on the 24VDC supply.

2.After a brief test sequence the Status display should show the node number, for example (the factory preset). If the display is not lit then re-check the power supply connections.

The NextMove BXII is now ready to be configured using WorkBench v5.

5-2 Operation

MN1904

Image 42

Baldor BXII installation manual Power on checks, 5-2Operation, MN1904

Contents

MOTION CONTROL Installation ManualNextMove BXII Motion Controller 9/02Page Contents 5 Operation A Accessories 6 Troubleshooting7 Specifications Appendicesiv Contents MN19041 General Information MN1904General Information 1-2General Information Safety NoticePrecautions MN19042.1 NextMove BXII features 2 IntroductionInstalled in 2.2 Receiving and inspection2.2.1Identifying the catalog number 2.3 Units and abbreviations 2-4Introduction MN19043.1 Introduction 3 Basic Installation3.1.1 Power sources 3.1.2 PC Hardware requirements3-2Basic Installation 3.1.4 Other information needed for installation3.1.3 Tools and miscellaneous hardware MN1904See also page All dimensions shown as mm inches This completes the basic installation3.2.1 Mounting the NextMove BXII Allow additional depth to accommodate wiring4.2 Connector locations - top panel 4.1 Introduction4 Input / Output 4.3 Connector locations - front panel 4.4 Power connections 4.4.1 Power4.5 Analog I/O 4.5.1Analog inputsAIN0 Pin AIN1 Pin 4.5.2 Analog outputs Demands 4-6Input / OutputMN1904 4.6 Digital I/O 4.6.1 Digital inputs 4-8Input / OutputMN1904 4.6.2 Digital inputs 4.6.3 Digital inputs Interrupts 4-10Input / OutputMN1904 Name 4.6.4 Digital outputsLocation Mint keyword / description4.7 Other I/O 4.7.1 Encoder interfaces - X9, X10, X114.7.2 Encoder input frequency 4.7.3 Relay and user power 4-14Input / OutputMN1904 4.7.4 RS232 Pin NameDescription NextMove BXII GND RS232RXD TXD DTE RTS CTSNextMove BXII 4.7.5 Connecting Baldor HMI Operator PanelsBaldor HMI PLC PORTMN1904 4.7.6 RS422 / RS4854-18Input / Output 4 NCNetwork slave Figure 12 - 4-wireRS485 multi-dropconnectionsNetwork master Network slave4.7.7 CAN connectors 4-20Input / OutputMN1904 4.7.8 CANopen 4.7.9 Baldor CAN4.8 Reset states 4.8.1 System watchdogEnable 4.9 Connection summary - minimum system wiringError out Host PCTable 2 - Minimum system wiring connections connectorsignal 4-24Input / Output5.1 Introduction 5.1.1 Connecting the NextMove BXII to the PC5.1.2 Installing the software 5 Operation5.1.5 Power on checks 5-2OperationMN1904 5.2 WorkBench 5.2.1 Help file5.2.2Starting WorkBench 5-4OperationMN1904 Click Scan to search for the NextMove BXII 5.3 Configuring an axis 5.3.1 Selecting a scale5.3.2Setting the drive enable output 5.3.3Testing the drive enable output 5-8OperationMN1904 5.4 Testing and tuning 5.4.1 Testing the drive command output6.To remove the demand and stop the test, type 5-10OperationMN1904 STOP.05.5 An introduction to closed loop control 5-12Operation MN1904MN1904 OperationFigure 16 - The NextMove BXII servo loop 5.6 Tuning an axis for current control 5.6.1 Selecting servo loop gainsThe distance depends on the scale set in 5.6.2 Underdamped response 5-16OperationMN1904 5.6.3 Overdamped response Figure 18 - Overdamped responseMN1904 5.6.4 Critically damped response5-18Operation Demand position Measured position5.7 Eliminating steady-stateerrors 5.8 Tuning an axis for velocity control 5.8.1 Calculating KVELFF=10.24 5-22Operation MN1904Figure 20 - Correct value of KVELFF 5.8.2 Adjusting KPROP 2. Click GoFigure 21 - Correct value of KPROP 5-24OperationMN1904 Demand position Measured position5.9 Digital input/output configuration 5.9.1 Digital input configuration5.9.2 Digital output configuration 5-26OperationMN1904 5.10 Saving setup information 1.In the Toolbox, click the Edit & Debug icon5.11Loading saved information 5-28OperationMN1904 6.1.2 SupportMet feature 6 Troubleshooting6.1.1 Problem diagnosis 6.1 Introduction6.2 NextMove BXII indicators 6.2.1 Status displayOffset move. The axis is performing an offset move 6.2.2 Motor control 6-4TroubleshootingMN1904 6.2.3 Communication 6-6Troubleshooting MN1904Introduction 7 SpecificationsInput power 7.1.1Digital inputs 7.1.3 Analog outputs Demands7.1.4 7.1.57.1.9 CAN interfaces 7.1.7 Relay output7.1.8 Encoder interfaces Update interval7-4Specifications 7.1.11Weights and dimensions7.1.10Environmental MN1904A Accessories A A.1 IntroductionA.1.1 Baldor CAN nodes A.1.2 Encoder Splitter/Buffer board A-2AccessoriesMN1904 Index Page Page Index MN1904continued CommentsComment CommentsComments MN1904Thank you for taking the time to help us Page Europe AustraliaMexico Singapore