Barco Projection Systems

GRAPHICS 808s

R9000901

R9000908

OWNER'S MANUAL

Date :	Art. No. :
051196	R5975007

Page 2

Image 2

Barco R9000908, R9000901 owner manual Barco Projection Systems, Date Art. No 051196 R5975007

Contents

Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007 Barco nv/Projection Systems Noordlaan Kuurne Belgium Table of Contents Service mode Options Safety Instructions On safety On servicing On installationOn cleaning On repacking Location and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Switching On/Off AC Power mains Cord ConnectionPower Check Connections Comp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white image Video input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selection Analog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selection Connecting a Component Video source to port 4/5 To select the component video input Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Battery installation in the RCU Controlling How to control the projector How to use your RCUHardware set up of the projector address Using your RCU Input selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Analog Picture Controls Controlling chained projectors Start UP of the Adjustment Mode Adjustment Mode 0000 Wrong Starting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Crt faceplate border Raster Shift AdjustmentProjected raster Raster Shift LEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Seagull Correction Seagull correctionLeft Side Correction Left Side Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Horizontal Size Adjustment Exit will return to Geometry Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Top blanking Right blanking Bottom blanking Convergence Adjustment Convergence Service Mode Starting up the Service modeOverview flowchart Service mode Copy a block Copy ModeIdentification Graphics 808s Deleting block by block Delete ModeDeletion of blocks Deletion of all blocks Run time Change passwordChange Language Barcographics 808s Convergence Mid Set to midpositionUndo Midposition Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP 003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft Version Options Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cables Orbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave Toggle Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card

BARCO PROJECTION SYSTEMS

GRAPHICS 808s

Date :

Art. No. :

051196

R5975007