Starting up the Service mode, Service Mode | Barco R9000908 specs

Service Mode

7	SERVICE MODE

Starting up the Service mode.

Use the control stick to highlight 'Service' and then press ENTER.

Some items in the Service mode are password protected (when the password function is active). Enter your password to continue. All other password protected items are now also free available if you stay in the adjustment mode.

ENTER continues to the Service Mode main menu. EXIT returns to the Operational mode.

The service items are combined in two service menus. To switch from the first to the second menu or vice versa, push the control stick forward or backward to select 'more...'

Overview flowchart 'Service' mode.

IDENTIFICATION

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

SERVICE MODE

RUN TIME

G2 ADJUSTMENT

GAMMA CORRECTIONS

CRT RUN IN CYCLE

PROJECTOR WARM UP

CRT DRIVE MODE

ADJUSTMENT MODE
Select a path from
below :
GUIDED
RANDOM ACCESS
INSTALLATION
SERVICE
IRIS
source 1
SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELTE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
Select with	or
then <ENTER>
<EXIT> to return.

SERVICE MODE

G2 ADJUSTMENT

GAMMA CORRECTIONS

CRT RUN IN CYCLE

PROJECTOR WARM UP

CRT DRIVE MODE

MORE...

Select with or then <ENTER> <EXIT> to return.

5975007 BARCOGRAPHICS 808s 160996		7-1

Image 38

Barco R9000908, R9000901 owner manual Starting up the Service mode, Overview flowchart Service mode, Service Mode

Contents

Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007 Barco nv/Projection Systems Noordlaan Kuurne Belgium Table of Contents Service mode Options Safety Instructions On safety On servicing On installationOn cleaning On repacking Location and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Switching On/Off AC Power mains Cord ConnectionPower Check Connections Comp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white image Video input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selection Analog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selection Connecting a Component Video source to port 4/5 To select the component video input Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Battery installation in the RCU Controlling How to control the projector How to use your RCUHardware set up of the projector address Using your RCU Input selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Analog Picture Controls Controlling chained projectors Start UP of the Adjustment Mode Adjustment Mode 0000 Wrong Starting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Crt faceplate border Raster Shift AdjustmentProjected raster Raster Shift LEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Seagull Correction Seagull correctionLeft Side Correction Left Side Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Horizontal Size Adjustment Exit will return to Geometry Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Top blanking Right blanking Bottom blanking Convergence Adjustment Convergence Service Mode Starting up the Service modeOverview flowchart Service mode Copy a block Copy ModeIdentification Graphics 808s Deleting block by block Delete ModeDeletion of blocks Deletion of all blocks Run time Change passwordChange Language Barcographics 808s Convergence Mid Set to midpositionUndo Midposition Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP 003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft Version Options Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cables Orbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave Toggle Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card