Invalid RWI soft Version, I2C error Addr FH3 | Barco R9000901

Messages, warnings and failure codes

WARNING :

go to

stand by

WARNING :

invalid

frequency

input

WARNING :

default settings loaded in the E2PROM

table is deleted

FAILURE

invalid

RWI soft

version

FAILURE

I2C error

addr. : 7FH3

FAILURE

short

circuit on I2C bus

Projector will switch to 'stand-by'when the RCVDS is no longer available.

The entered frequency or ap- plied frequency of the source is out of the projector's range.

Adjustment settings are lost. Re- load using Projector Control Soft- ware via PC or MAC (if this op- tion is available), or readjust im- age.

Message to inform that selected table is deleted. This message will be followed by 'confirm mes- sage', on which the user has to answer.

Wrong software version in your projector. Call for technical sup- port.

Hardware failure. Call a quali- fied service technician for repair.

Hardware failure. Call a quali- fied service technician for repair.

FAILURE

RCVDS com- munication error

FAILURE

RWI commu-

nication

error

FAILURE

IRIS commu-

nication

error

WAIT

starting

up

IRIS

Serial communication error be- tween RCVDS800 and projec- tor.

Hardware failure. Call a quali- fied service technician.

Communication error between IRIS 800 and the projector. Call a qualified service technician.

Message during the start up of the IRIS 800. Message will dis- appear when the IRIS 800 is ready to accept commands.

8-2		5975007 BARCOGRAPHICS 808s 160996

Image 47

Barco R9000901 Invalid RWI soft Version, I2C error Addr FH3, Short Circuit on I2C bus, RWI commu Nication Error, Starting

Contents

Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Options Service mode On safety Safety Instructions On repacking On installationOn cleaning On servicing Location and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Connections AC Power mains Cord ConnectionPower Check Switching On/Off Start up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. Video Input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selection RGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input Selection To select the component video input Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Controlling Battery installation in the RCU Using your RCU How to use your RCUHardware set up of the projector address How to control the projector Input selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Controlling chained projectors Analog Picture Controls Adjustment Mode Start UP of the Adjustment Mode Wrong 0000 Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment mode From next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Raster Shift AdjustmentProjected raster Crt faceplate border LEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Seagull Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Exit will return to Geometry Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence Adjustment Service Mode Starting up the Service modeOverview flowchart Service mode Graphics 808s Copy ModeIdentification Copy a block Deletion of all blocks Delete ModeDeletion of blocks Deleting block by block Barcographics 808s Change passwordChange Language Run time Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP 003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication Error Options Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card