Insert Card

Insert Card

RCU

INPUT SOURCES

PROJECTOR

INPUT SOURCES

RCVDS

RCU

INPUT SOURCES

PROJECTOR

INPUT SOURCES

RCVDS

5975007 BARCOGRAPHICS 808s 160996		i-1

Page 55

Image 55

Barco R9000901, R9000908 owner manual Insert Card

Contents

Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Options Service mode On safety Safety Instructions On repacking On installationOn cleaning On servicing Location and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology Connections AC Power mains Cord ConnectionPower Check Switching On/Off Start up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. Video Input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selection RGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input Selection To select the component video input Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Controlling Battery installation in the RCU Using your RCU How to use your RCUHardware set up of the projector address How to control the projector How to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture Controls Adjustment Mode Start UP of the Adjustment Mode Wrong 0000 Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Raster Shift AdjustmentProjected raster Crt faceplate border LEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Left Side Correction Seagull correctionLeft Side Correction Seagull Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Exit will return to Geometry Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence Adjustment Overview flowchart Service mode Starting up the Service modeService Mode Graphics 808s Copy ModeIdentification Copy a block Deletion of all blocks Delete ModeDeletion of blocks Deleting block by block Barcographics 808s Change passwordChange Language Run time Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP Fh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication Error Options Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card