Orbiting Speed Toggle only in Master Orbiting | Barco R9000901

Orbiting

Orbiting Speed Toggle (only in MASTER Orbiting)

Highlight 'SPEED : SLOW' with the control stick and press ENTER to set the ORBITING SPEED to Fast.

Highlight 'SPEED : FAST' with the control stick and press ENTER to set the ORBITING SPEED to Slow

ENTER continues to Set up Orbiting

EXIT returns to path selection menu

ADJUST returns to operational mode.

Orbiting Alignment

Preparation :

Before proceeding to the alignment of the Orbiting default settings, be sure that the Horizontal Phase and the Raster shift are correctly aligned with the Orbiting mode set to OFF.

This alignment must be performed in case of a multiple projector installation with Master and Slave projectors in order to ensure a correct operation of the Orbiting for all projectors.

Adjustment procedure Stand-Alone projector :

Highlight 'ADJUST DEVIATION' with the control stick and press

ENTER.

When adjusting the horizontal and the vertical deviation, the picture moves in the corresponding direction, allowing the set up of the deviation without orbiting operation.

Push the control stick to the right or backward to toggle between Hor. and Vert. deviation andjustment.

Adjust horizontal deviation by pushing the control stick to the left or to the right

Adjust vertical deviation by pushing the control stick forward or backward

MASTER ORBITING
CHANGE TO MASTER
MODE : ON
SPEED : FAST
ADJUST DEVIATION
SELECT WITH	OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH	OR
HORIZONTAL WITH	OR
<EXIT> to return.

SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH	OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH	OR
HORIZONTAL WITH	OR
<EXIT> to return.

HORIZONTAL

ORBIT AMPL

70

VERTICAL

ORBIT AMPL

70

A-2		5975007 BARCOGRAPHICS 808s 160996

Image 51

Barco R9000901, R9000908 owner manual Orbiting Speed Toggle only in Master Orbiting, Orbiting Alignment

Contents

Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Options Service mode On safety Safety Instructions On repacking On installationOn cleaning On servicing Location and Function of Controls Getting Access Control panel terminology Local KeypadRCU control panel terminology Connections AC Power mains Cord ConnectionPower Check Switching On/Off Start up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. Video Input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selection RGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input Selection To select the component video input Connecting a Component Video source to port 4/5 Connecting a Rcvds 05 switcher to the Barcographics 808s Connecting a VS05 switcher to Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Controlling Battery installation in the RCU Using your RCU How to use your RCUHardware set up of the projector address How to control the projector How to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture Controls Adjustment Mode Start UP of the Adjustment Mode Wrong 0000 Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment mode From next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Raster Shift AdjustmentProjected raster Crt faceplate border Left-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Left Side Correction Seagull correctionLeft Side Correction Seagull Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Exit will return to Geometry Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence Adjustment Starting up the Service mode Overview flowchart Service modeService Mode Graphics 808s Copy ModeIdentification Copy a block Deletion of all blocks Delete ModeDeletion of blocks Deleting block by block Barcographics 808s Change passwordChange Language Run time Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP MESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication Error Options Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Adjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card