Convergence Adjustment | Barco R9000901, R9000908 specification

Random Access Adjustment Mode

Convergence Adjustment

Convergence adjustments affect both the horizontal and vertical lines of the setup pattern. These adjustments are performed on the red image while superimposed on the green image and then on the blue image while superimposed on the green image.

Note : the green convergence adjustments can be added as an option. When these are available, always start with 'green only'. This option will also be indicated on the convergence menu.

Highlight first 'Green only' when available with the control stick and press ENTER to display the convergence adjustment menu

RANDOM ACCESS

ADJUSTMENT MODE

PICTURE TUNING

GEOMETRY

CONVERGENCE

FOCUSING

COLOR SELECT

ORBITING

CONTR. MODULATION

SOFT EDGE

CONVERGENCE

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

CONVERGENCE

SEL : select area

using

arrow keys

ADJ : adjust area

using

arrow keys

Toggle between SEL and ADJ with <ENTER> <ENTER> continue <EXIT> to return

The screen area is divided into 25 areas. Use the control stick to move the box to the desired zone and then press ENTER to begin the convergence adjustment. Start the convergence adjustment with zone one and continue as mentioned in the diagram hereafter.

Use the control stick to make horizontal or vertical convergence adjustments in the selected zone and then press ENTER to move the box to another zone or EXIT to return to the Convergence menu.

ENTER toggles arrow keys between zone selection and zone adjust- ment .

EXIT returns to convergence menu

25 23 9 15 17

24 22 8 14 16

5

4

1

2

3

20 18 6 10 12

21 19 7 11 13

CONVERGE ADJUSTMENT

70

green image

red image

6-16		5975007 BARCOGRAPHICS 808S 051196

Image 37

Barco R9000901, R9000908 owner manual Convergence Adjustment

Contents

Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Options Service mode On safety Safety Instructions On cleaning On installationOn servicing On repacking Location and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology Power Check AC Power mains Cord ConnectionSwitching On/Off Connections Port No Projector input Press Digit Button Signal Input Connection to the ProjectorComp. Video Video1/Comp. Video Start up with full white image Connecting a S-Video or Video source to port Connecting a Composite Video source to portVideo input selection Input selection Connecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portAnalog Input Selection RGB input selection To select the component video input Connecting a Component Video source to port 4/5 Connecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Controlling Battery installation in the RCU Hardware set up of the projector address How to use your RCUHow to control the projector Using your RCU How to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture Controls Adjustment Mode Start UP of the Adjustment Mode Wrong 0000 Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Line Doubler option Port 2 Video or S-VideoColor Select Color Select Focusing Horizontal Phase Adjustment Geometry AdjustmentsGeometry Geometry Projected raster Raster Shift AdjustmentCrt faceplate border Raster Shift LEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Left Side Correction Seagull correctionSeagull Correction Left Side Correction TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S Exit will return to Geometry Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence Adjustment Overview flowchart Service mode Starting up the Service modeService Mode Identification Copy ModeCopy a block Graphics 808s Deletion of blocks Delete ModeDeleting block by block Deletion of all blocks Change Language Change passwordRun time Barcographics 808s Undo Midposition Set to midpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm Up CRT Drive ModeProjector Warm UP Projector Warm UP Fh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available RWI commu Nication Error I2C error Addr FH3Iris commu Nication Error Invalid RWI soft Version Options Orbiting Kit Magik Interface Ceiling Mount kit CM100Line Doubler Kit Adapter and communication cables Orbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave Toggle Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card