Manuals / Barco / Computer Equipment / Projector

Barco R9000908, R9000901 owner manual Adjustment Blocks and Source Numbers

Models: R9000901 R9000908

1 55

Download 55 pages 19.89 Kb

Page 54

Adjustment Blocks and Source Numbers 90-99

The alternate adjustment block for sources 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector) is activated by selecting the corresponding source number 0 - 9 (projector with RCVDS) or 1 - 5 (stand-alone projector). Once this source number is selected, the alternate block of adjustment data is in use and may be modified via the adjust mode of the projector. The alternate adjustment block is automatically stored.

Follow the steps below to create a second adjustment block for a source between 0 and 9.

1.Select the source between 0 and 9 that the second adjustment block is to be created for.

2.Select the corresponding source number between 90 and 99. The adjustment block for the source number between 0 and 9 is copied to the corresponding source number between 90 and 99.

3.Enter the adjust mode and make any desired changes (geometry, convergence, sync fast/slow, enhanced blue on/off) to the second adjustment block.

4.Exit the adjust mode.

Note : the above also applies to source number 1 - 5 and 91 - 95 of a stand alone projector (no RCVDS)

B-2		5975007 BARCOGRAPHICS 808s 160996

Image 54

Barco R9000908, R9000901 owner manual Adjustment Blocks and Source Numbers

Contents

OWNERS MANUAL GRAPHICS 808s R9000901 R9000908051196 DateArt. No R5975007BARCO nv/Projection Systems Noordlaan B-8520 Kuurne Belgium Printed in BelgiumTable of Contents Table of contentsTable of Contents Service modeOptions Messages, warnings and failuresOn safety SAFETY INSTRUCTIONSSafety Instructions Notice on SafetyA. Mains lead Power cord with CEE 7 plug On installationOn cleaning B. Power cord with ANSI 73.11 plug75 ohm Termination Switch for S-Video signals AC Power InputPort 4/5 RGB-S Input 5x BNC connector 75 ohm Termination Switch for Video signalsb. RCU control panel terminology Getting AccessControl panel terminology a. The Local Keypad Location and Functions of ControlSwitching On/Off AC Power mains Cord ConnectionPower Check 3 CONNECTIONSProjector input Signal Input Connection to the ProjectorPort No Press Digit ButtonVideo input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selectionRGB R, G, B signals with automatic sync detection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input SelectionConnecting a Component Video source with Tri- level sync to port 4/5 Connecting a RGB Analog source with Tri-level sync to port 4/5 optionConnecting a Component Video source to port 4/5 RG3sB R, G, B signals with automatic Tri-level sync detectionConnecting an IR Remote Receiver to the BARCOGRAPHICS 808s Connecting a RCVDS 05 switcher to the BARCOGRAPHICS 808sConnecting a VS05 switcher to the BARCOGRAPHICS 808s PERIPHERAL EQUIPMENTBattery installation in the RCU 4 CONTROLLINGControlling b. How to control the projector How to use your RCUa. hardware set up of the projector address c. Using your RCUInput selection How to display a projector address?How to program an address into the RCU? Press DigitBrightness Control Analog Picture ControlsControlling chained projectors Contrast ControlAdjustment Mode START UP OF THE ADJUSTMENT MODEStart Up of the Adjustment Mode Warning during the start up of the installation modepassword 0000Start Up of the Adjustment Mode enterStarting-Up the Random Access Adjustment mode RANDOM ACCESS ADJUSTMENT MODERandom Access Adjustment Mode Overview Random Access Adjustment modeRandom Access Adjustment Mode ENTER Selecting Setup PatternInternal Cross Hatch Pattern Random Access Adjustment ModeColor Balance Random access adjustment mode selection menuPicture Tuning Fixed Color BalancePeaking Sync Fast/Slow AdjustmentClamp Tuning Random Access Adjustment ModeColor Select Port 2 Video or S-VideoLine Doubler option Random Access Adjustment ModeMidpoint focusing FocusingFocusing color select Top image focusingRandom Access Adjustment Mode Geometry AdjustmentsHorizontal Phase Adjustment GEOMETRYcrt faceplate border Raster Shift Adjustmentprojected raster Random Access Adjustment ModeCorrects the tilting of the vertical lines in the middle of the image Left-Right east-west AdjustmentsRandom Access Adjustment Mode Corrects for curvature of the vertical lines on the right sideSeagull correction Left Side CorrectionRandom Access Adjustment Mode Top-Bottom north-south Adjustments Random Access Adjustment ModeHorizontal Size Adjustment Seagull CorrectionRandom Access Adjustment Mode Random Access Adjustment Mode Vertical Linearity AdjustmentVertical Size Adjustment V LINEARITYLeft blanking Blanking AdjustmentsRandom Access Adjustment Mode Top blanking Right blanking Bottom blankingConvergence Adjustment Random Access Adjustment ModeCONVERGE ADJUSTMENT Starting up the Service mode SERVICE MODEService Mode Overview flowchart Service modeGRAPHICS 808s IdentificationCopy a block Service ModeDeletion of all blocks Deletion of blocksDeleting block by block Service ModeRun time Change passwordChange Language 5975007 BARCOGRAPHICS 808sConvergence Mid Set to midpositionUndo Midposition Undo Convergence MidpositionDynamic Astigmatism spot shape adjustment Service ModeDYNAMIC ASTIGMATISM CRT run in cycle G2 AdjustGamma corrections Service ModeService Mode Projector Warm UpCRT Drive Mode PERMANENT BOOST MODE IN USE8 MESSAGES, WARNINGS AND FAILURE CODES password xxxx text on text off PROJECTOR ADDRESS 003input no longer available check input signal or select new source Messages, warnings and failure codesFAILURE RWI commu nication error FAILURE IRIS commu nication error default settings loaded in the E2PROM table is deleted FAILUREinvalid RWI soft version FAILURE I2C error addr. 7FH3 FAILURE short go to stand by9 OPTIONS Hardwired RCUVS05 Switcher OptionsOrbiting Kit MAGIK InterfaceCeiling Mount kit CM100 Line Doubler KitOrbiting Orbiting Mode Toggle SwitchesA ORBITING Orbiting optionOrbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in MASTER Orbiting OrbitingAdjustment procedure multiple projector installations OrbitingAdjustment Blocks memory blocks ADJUSTMENT BLOCKS AND SOURCEAdjustment Blocks and Source Numbers Scan Switch ConfigurationAdjustment Blocks and Source Numbers INPUT SOURCES INSERT CARDInsert Card PROJECTOR