Manuals / Barco / Computer Equipment / Projector

Barco R9000908, R9000901 Adjustment procedure multiple projector installations, Orbiting

Models: R9000901 R9000908

1 55

Download 55 pages 19.89 Kb

Page 52

Adjustment procedure multiple projector installations :

Orbiting

Adjustment procedure multiple projector installations :

Inportant : to allow corrections in the deviation alignments of the slave projectors, never adjust the deviations of the master projector to its maximum.

Default setting of the Master projectorn see 'Stand-Alone projector'.

Highlight 'ADJUST DEVIATION' by pushing the control stick forward or backward and press ENTER.

When adjusting the horizontal and the vertical deviation, the picture moves in corresponding direction, allowing the set up of the deviation without orbiting operation.

Push the control stick to the right or backward to toggle between Hor. and Vert. deviation adjustment.

Adjust horizontal deviation by pushing the control stick to the left or to the right

Adjust vertical deviation by pushing the control stick forward or backward

SLAVE ORBITING
CHANGE TO MASTER
ADJUST DEVIATION
SELECT WITH	OR
THEN <ENTERN>
DEVIATION ADJUST :
VERTICAL WITH	OR
HORIZONTAL WITH	OR
<EXIT> to return.

HORIZONTAL

ORBIT AMPL

70

VERTICAL

ORBIT AMPL

70

5975007 BARCOGRAPHICS 808s 160996		A-3

Image 52

Barco R9000908, R9000901 owner manual Adjustment procedure multiple projector installations, Orbiting

Contents

OWNERS MANUAL GRAPHICS 808s R9000901 R9000908Date Art. No051196 R5975007BARCO nv/Projection Systems Noordlaan B-8520 Kuurne Belgium Printed in BelgiumTable of Contents Table of contentsService mode OptionsTable of Contents Messages, warnings and failuresSAFETY INSTRUCTIONS Safety InstructionsOn safety Notice on SafetyOn installation On cleaningA. Mains lead Power cord with CEE 7 plug B. Power cord with ANSI 73.11 plugAC Power Input Port 4/5 RGB-S Input 5x BNC connector75 ohm Termination Switch for S-Video signals 75 ohm Termination Switch for Video signalsGetting Access Control panel terminology a. The Local Keypadb. RCU control panel terminology Location and Functions of ControlAC Power mains Cord Connection Power CheckSwitching On/Off 3 CONNECTIONSSignal Input Connection to the Projector Port NoProjector input Press Digit ButtonConnecting a Composite Video source to port Connecting a S-Video or Video source to portVideo input selection Input selectionConnecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5RGB R, G, B signals with automatic sync detection Analog Input SelectionConnecting a RGB Analog source with Tri-level sync to port 4/5 option Connecting a Component Video source to port 4/5Connecting a Component Video source with Tri- level sync to port 4/5 RG3sB R, G, B signals with automatic Tri-level sync detectionConnecting a RCVDS 05 switcher to the BARCOGRAPHICS 808s Connecting a VS05 switcher to the BARCOGRAPHICS 808sConnecting an IR Remote Receiver to the BARCOGRAPHICS 808s PERIPHERAL EQUIPMENT4 CONTROLLING Battery installation in the RCUControlling How to use your RCU a. hardware set up of the projector addressb. How to control the projector c. Using your RCUHow to display a projector address? How to program an address into the RCU?Input selection Press DigitAnalog Picture Controls Controlling chained projectorsBrightness Control Contrast ControlSTART UP OF THE ADJUSTMENT MODE Start Up of the Adjustment ModeAdjustment Mode Warning during the start up of the installation mode0000 Start Up of the Adjustment Modepassword enterRANDOM ACCESS ADJUSTMENT MODE Random Access Adjustment ModeStarting-Up the Random Access Adjustment mode Overview Random Access Adjustment modeRandom Access Adjustment Mode Selecting Setup Pattern Internal Cross Hatch PatternENTER Random Access Adjustment ModeRandom access adjustment mode selection menu Picture TuningColor Balance Fixed Color BalanceSync Fast/Slow Adjustment Clamp TuningPeaking Random Access Adjustment ModePort 2 Video or S-Video Line Doubler optionColor Select Random Access Adjustment ModeFocusing Focusing color selectMidpoint focusing Top image focusingGeometry Adjustments Horizontal Phase AdjustmentRandom Access Adjustment Mode GEOMETRYRaster Shift Adjustment projected rastercrt faceplate border Random Access Adjustment ModeLeft-Right east-west Adjustments Random Access Adjustment ModeCorrects the tilting of the vertical lines in the middle of the image Corrects for curvature of the vertical lines on the right sideLeft Side Correction Seagull correctionRandom Access Adjustment Mode Top-Bottom north-south Adjustments Random Access Adjustment ModeSeagull Correction Horizontal Size AdjustmentRandom Access Adjustment Mode Vertical Linearity Adjustment Vertical Size AdjustmentRandom Access Adjustment Mode V LINEARITYBlanking Adjustments Random Access Adjustment ModeLeft blanking Top blanking Right blanking Bottom blankingRandom Access Adjustment Mode Convergence AdjustmentCONVERGE ADJUSTMENT SERVICE MODE Service ModeStarting up the Service mode Overview flowchart Service modeIdentification Copy a blockGRAPHICS 808s Service ModeDeletion of blocks Deleting block by blockDeletion of all blocks Service ModeChange password Change LanguageRun time 5975007 BARCOGRAPHICS 808sSet to midposition Undo MidpositionConvergence Mid Undo Convergence MidpositionService Mode Dynamic Astigmatism spot shape adjustmentDYNAMIC ASTIGMATISM G2 Adjust Gamma correctionsCRT run in cycle Service ModeProjector Warm Up CRT Drive ModeService Mode PERMANENT BOOST MODE IN USEpassword xxxx text on text off PROJECTOR ADDRESS 003 input no longer available check input signal or select new source8 MESSAGES, WARNINGS AND FAILURE CODES Messages, warnings and failure codesdefault settings loaded in the E2PROM table is deleted FAILURE invalid RWI soft version FAILURE I2C error addr. 7FH3 FAILURE shortFAILURE RWI commu nication error FAILURE IRIS commu nication error go to stand byHardwired RCU VS05 Switcher9 OPTIONS OptionsMAGIK Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler KitOrbiting Mode Toggle Switches A ORBITINGOrbiting Orbiting optionAdjustment procedure Stand-Alone projector Orbiting Speed Toggle only in MASTER OrbitingOrbiting Alignment OrbitingAdjustment procedure multiple projector installations OrbitingADJUSTMENT BLOCKS AND SOURCE Adjustment Blocks and Source NumbersAdjustment Blocks memory blocks Scan Switch ConfigurationAdjustment Blocks and Source Numbers INSERT CARD Insert CardINPUT SOURCES PROJECTOR