0000, Wrong | Barco R9000901, R9000908 instruction

Start Up of the Adjustment Mode

Some items in the Adjustment mode are password protected. While selecting such an item, the projector asks you to enter your password. (Password protection is only available when the password DIP switch on the controller module is in the ON position. Contact a BARCO authorized technician when no password is requested during the adjustment procedure and password protection is desired.)

Your password contains 4 digits.

Enter the digits with the numeric keys on the RCU.

Example : 2 3 1 9

For each digit entered, a 'X' appears on the screen under the displayed text 'enter password'.

When your password is correct, you get access to the 'Adjustment item'. When the entered password is wrong, The message 'Wrong password !!!' will be displayed. The projector stays on the previous selected item.

Factory programmed password :

0000

Once the password is correctly entered, all other password protected items are accessible without re-entering your password.

When re-entering the Adjustment mode, it will be necessary to enter your password again when selecting a password protected item.

enter

password

xxxx

197

WRONG

PASSWORD

!!!

5-2		5975007 BARCOGRAPHICS 808S 160996

Image 21

Barco R9000901, R9000908 owner manual 0000, Wrong

Contents

Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Options Service mode On safety Safety Instructions On cleaning On installationOn servicing On repacking Location and Function of Controls Getting Access Control panel terminology Local KeypadRCU control panel terminology Power Check AC Power mains Cord ConnectionSwitching On/Off Connections Port No Projector input Press Digit Button Signal Input Connection to the ProjectorComp. Video Video1/Comp. Video Start up with full white image Connecting a S-Video or Video source to port Connecting a Composite Video source to portVideo input selection Input selection Connecting a RGB Analog source to port 4/5 Connecting a RGB Analog source to portAnalog Input Selection RGB input selection To select the component video input Connecting a Component Video source to port 4/5 Connecting a Rcvds 05 switcher to the Barcographics 808s Connecting a VS05 switcher to Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Controlling Battery installation in the RCU Hardware set up of the projector address How to use your RCUHow to control the projector Using your RCU How to display a projector address? How to program an address into the RCU?Input selection Port No Projector input Press Digit Button Controlling chained projectors Analog Picture Controls Adjustment Mode Start UP of the Adjustment Mode Wrong 0000 Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment mode From next Selecting Setup Pattern Internal Cross Hatch PatternInternal # Pattern Random access adjustment mode selection menu Picture TuningColor Balance Sync Fast/Slow Adjustment Clamp TuningPeaking Line Doubler option Port 2 Video or S-VideoColor Select Color Select Focusing Horizontal Phase Adjustment Geometry AdjustmentsGeometry Geometry Projected raster Raster Shift AdjustmentCrt faceplate border Raster Shift Left-Right east-west Adjustments LEFT-RIGHT E-WLEFT-RIGHT Left Side Correction Seagull correctionSeagull Correction Left Side Correction TOP-BOTTOM Top-Bottom north-south AdjustmentsTOP-BOTTOM N-S TOP-BOTTOM N-S Exit will return to Geometry Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence Adjustment Starting up the Service mode Overview flowchart Service modeService Mode Identification Copy ModeCopy a block Graphics 808s Deletion of blocks Delete ModeDeleting block by block Deletion of all blocks Change Language Change passwordRun time Barcographics 808s Undo Midposition Set to midpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism spot shape adjustment Dynamic AstigmatismDynamic Astigmatism G2 Adjust Gamma correctionsCRT run in cycle Projector Warm Up CRT Drive ModeProjector Warm UP Projector Warm UP MESSAGES, Warnings and Failure Codes Fh= 15.6 kHz Fv= 050 Hz003 Input not available RWI commu Nication Error I2C error Addr FH3Iris commu Nication Error Invalid RWI soft Version Options Orbiting Kit Magik Interface Ceiling Mount kit CM100Line Doubler Kit Adapter and communication cables Orbiting Orbiting Mode Toggle SwitchesOrbiting option Master/Slave Toggle Adjustment procedure Stand-Alone projector Orbiting Speed Toggle only in Master OrbitingOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks and Source Adjustment Blocks memory blocksSource numbers 90 Adjustment Blocks and Source Numbers Insert Card