Deletion of blocks, Deleting block by block | Barco R9000908

Service Mode

Deletion of blocks

This item is password protected.

The delete function is used to clear all data (settings) from an adjustment block.

A delete can be given :

-block by block

or

-for all blocks.

Deleting block by block

The delete a block function deletes the settings of a selected block. Highlight 'Delete a block' with the control stick and press ENTER.

Push the control stick forward or backward to select the desired adjustment block. Press ENTER to delete the selected adjustment block. A confirmation menu will be displayed.

ENTER will delete the selected block.

EXIT cancels the deletion procedure and returns to the Service mode main menu.

SERVICE MODE
IDENTIFICATION
COPY A BLOCK
DELETE A BLOCK
DELETE ALL BLOCKS
CHANGE PASSWORD
CHANGE LANGUAGE
RUN TIME
SET TO MIDPOSITION
CONVERGENCE MID
DYNAMIC ASTIGMATISM
MORE...
		DELETE MODE
Nr.	Src	Fh	Fv	inp	conf
1	1	15.6 50		video	FC
2	3	31.2 60		RGB3S	RT
3	-	15.6 50		intern	FC
4	2	31.5 50		RGB3S	FC
5	-	33.7 60		intern	FC
6
7
8
				Active block nr. 1
					DELETE BLOCK

The selected block will be deleted !

<ENTER> to confirm <EXIT> to cancel

Deletion of all blocks

Highlight 'delete all blocks' with the control stick and press ENTER. ENTER gives a confirmation message before deleting.

If you are certain you wish to delete all blocks, press ENTER to confirm, otherwise press EXIT to return.

Once ENTER is pressed, all block headers and adjustment settings are permanently removed and cannot be restored.

SERVICE MODE

IDENTIFICATION

COPY A BLOCK

DELETE A BLOCK

DELETE ALL BLOCKS

CHANGE PASSWORD

CHANGE LANGUAGE

RUN TIME

SET TO MIDPOSITION

CONVERGENCE MID

DYNAMIC ASTIGMATISM

MORE...

DELETE BLOCK

All block

will be deleted !

<ENTER> to confirm <EXIT> to cancel

5975007 BARCOGRAPHICS 808s 160996		7-3

Image 40

Barco R9000908, R9000901 owner manual Deletion of blocks, Deleting block by block, Deletion of all blocks, Delete Mode

Contents

Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007 Barco nv/Projection Systems Noordlaan Kuurne Belgium Table of Contents Service mode Options Safety Instructions On safety On installation On cleaningOn servicing On repacking Location and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology AC Power mains Cord Connection Power CheckSwitching On/Off Connections Signal Input Connection to the Projector Port No Projector input Press Digit ButtonComp. Video Video1/Comp. Video Start up with full white image Connecting a Composite Video source to port Connecting a S-Video or Video source to portVideo input selection Input selection Connecting a RGB Analog source to port Connecting a RGB Analog source to port 4/5Analog Input Selection RGB input selection Connecting a Component Video source to port 4/5 To select the component video input Connecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU Controlling How to use your RCU Hardware set up of the projector addressHow to control the projector Using your RCU How to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectors Start UP of the Adjustment Mode Adjustment Mode 0000 Wrong Starting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Port 2 Video or S-Video Line Doubler optionColor Select Color Select Focusing Geometry Adjustments Horizontal Phase AdjustmentGeometry Geometry Raster Shift Adjustment Projected rasterCrt faceplate border Raster Shift LEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull correction Left Side CorrectionSeagull Correction Left Side Correction Top-Bottom north-south Adjustments TOP-BOTTOMTOP-BOTTOM N-S TOP-BOTTOM N-S Horizontal Size Adjustment Exit will return to Geometry Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Top blanking Right blanking Bottom blanking Convergence Adjustment Convergence Overview flowchart Service mode Starting up the Service modeService Mode Copy Mode IdentificationCopy a block Graphics 808s Delete Mode Deletion of blocksDeleting block by block Deletion of all blocks Change password Change LanguageRun time Barcographics 808s Set to midposition Undo MidpositionConvergence Mid Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle CRT Drive Mode Projector Warm UpProjector Warm UP Projector Warm UP Fh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available I2C error Addr FH3 RWI commu Nication ErrorIris commu Nication Error Invalid RWI soft Version Options Magik Interface Ceiling Mount kit CM100 Orbiting KitLine Doubler Kit Adapter and communication cables Orbiting Mode Toggle Switches OrbitingOrbiting option Master/Slave Toggle Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card