From next | Barco R9000901, R9000908 specs

Random Access Adjustment Mode

From next page

RANDOM ACCESS

ADJUSTMENT MODE

SETUP PATTERN SELECTION

CONVERGENCE

FOCUSING

COLOR SELECT

ORBITING

H SIZE

VLINEARITY

V SIZE

BLANKING

GREEN ONLY

RED ON GREEN

BLUE ON GREEN

RED

GREEN

BLUE

RED

GREEN

BLUE

RED AND GREEN

BLUE AND GREEN

RED AND BLUE

TOP

BOTTOM

LEFT

RIGHT

CONTRAST MODULATION

SOFT EDGE CORRECTION

6-2		5975007 BARCOGRAPHICS 808S 051196

Page 23

Image 23

Barco R9000901, R9000908 owner manual From next

Contents

Graphics 808s R9000901 R9000908 Date Art. No 051196 R5975007 Barco Projection Systems Noordlaan Kuurne Belgium Barco nv/Projection Systems Table of Contents Options Service mode On safety Safety Instructions On repacking On installationOn cleaning On servicing Location and Function of Controls RCU control panel terminology Getting AccessControl panel terminology Local Keypad Connections AC Power mains Cord ConnectionPower Check Switching On/Off Start up with full white image Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Comp. Video Video1/Comp. Video Input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Video input selection RGB input selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 Analog Input Selection To select the component video input Connecting a Component Video source to port 4/5 Connecting an IR Remote Receiver to the Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting a VS05 switcher to Barcographics 808s Controlling Battery installation in the RCU Using your RCU How to use your RCUHardware set up of the projector address How to control the projector Input selection Port No Projector input Press Digit Button How to display a projector address?How to program an address into the RCU? Controlling chained projectors Analog Picture Controls Adjustment Mode Start UP of the Adjustment Mode Wrong 0000 Overview Random Access Adjustment mode Starting-Up the Random Access Adjustment mode From next Internal # Pattern Selecting Setup PatternInternal Cross Hatch Pattern Color Balance Random access adjustment mode selection menuPicture Tuning Peaking Sync Fast/Slow AdjustmentClamp Tuning Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Raster Shift Raster Shift AdjustmentProjected raster Crt faceplate border LEFT-RIGHT Left-Right east-west AdjustmentsLEFT-RIGHT E-W Left Side Correction Seagull correctionLeft Side Correction Seagull Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Exit will return to Geometry Horizontal Size Adjustment Vertical Size Adjustment Vertical Linearity Adjustment Top blanking Right blanking Bottom blanking Blanking Adjustments Convergence Convergence Adjustment Service Mode Starting up the Service modeOverview flowchart Service mode Graphics 808s Copy ModeIdentification Copy a block Deletion of all blocks Delete ModeDeletion of blocks Deleting block by block Barcographics 808s Change passwordChange Language Run time Undo Convergence Midposition Set to midpositionUndo Midposition Convergence Mid Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism CRT run in cycle G2 AdjustGamma corrections Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP 003 Input not available MESSAGES, Warnings and Failure CodesFh= 15.6 kHz Fv= 050 Hz Invalid RWI soft Version I2C error Addr FH3RWI commu Nication Error Iris commu Nication Error Options Adapter and communication cables Magik Interface Ceiling Mount kit CM100Orbiting Kit Line Doubler Kit Master/Slave Toggle Orbiting Mode Toggle SwitchesOrbiting Orbiting option Orbiting Alignment Adjustment procedure Stand-Alone projectorOrbiting Speed Toggle only in Master Orbiting Adjustment procedure multiple projector installations Source numbers 90 Adjustment Blocks and SourceAdjustment Blocks memory blocks Adjustment Blocks and Source Numbers Insert Card