Starting-Up the Random Access Adjustment mode | Barco R9000908

Random Access Adjustment Mode

6	RANDOM ACCESS ADJUSTMENT MODE

Starting-Up the Random Access Adjustment mode.

Push the control stick forward or backward to highlight "RANDOM ACCESS" and then press ENTER.

Some items in the Random access mode are password protected (when the password function is enabled). Enter your password to continue. All other password protected items are now also available if you stay in the adjustment mode.

ENTER continues to Setup Pattern Selection

EXIT returns to Operational mode

ADJUSTMENT MODE

Select a path from below :

GUIDED

RANDOM ACCESS INSTALLATION SERVICE IRIS

Source 01

Select with or

then <ENTER>

<EXIT> to return.

Overview 'Random Access Adjustment' mode

PICTURE TUNING

RANDOM ACCESS	GEOMETRY
ADJUSTMENT MODE

SETUP PATTERN SELECTION

COLOR BALANCE

SYNC

PEAKING

CLAMP TUNING

LINE DOUBLER

PORT 2

H PHASE

RASTER SHIFT

LEFT-RIGHT (E-W)

LEFT SIDE CORRECTIONS

TOP-BOTTOM (N-S)

V CENTERLINE BOW

V CENTERLINE SKEW

SIDE BOW

SIDE KEYSTONE

SEAGULL CORRECTION

LEFT KEYSTONE

LEFT BOW

H CENTERLINE BOW

H CENTERLINE SKEW

TOP KEYSTONE

TOP BOW

BOTTOM KEYSTONE

BOTTOM BOW

SEAGULL CORRECTION

To next page

To next page

5975007 BARCOGRAPHICS 808S 051196

6-1

Image 22

Barco R9000908, R9000901 owner manual Starting-Up the Random Access Adjustment mode, Overview Random Access Adjustment mode

Contents

Graphics 808s R9000901 R9000908 Barco Projection Systems Date Art. No 051196 R5975007 Barco nv/Projection Systems Noordlaan Kuurne Belgium Table of Contents Service mode Options Safety Instructions On safety On servicing On installationOn cleaning On repacking Location and Function of Controls Control panel terminology Local Keypad Getting AccessRCU control panel terminology Switching On/Off AC Power mains Cord ConnectionPower Check Connections Comp. Video Video1/Comp. Video Signal Input Connection to the ProjectorPort No Projector input Press Digit Button Start up with full white image Video input selection Connecting a Composite Video source to portConnecting a S-Video or Video source to port Input selection Analog Input Selection Connecting a RGB Analog source to portConnecting a RGB Analog source to port 4/5 RGB input selection Connecting a Component Video source to port 4/5 To select the component video input Connecting a VS05 switcher to Barcographics 808s Connecting a Rcvds 05 switcher to the Barcographics 808sConnecting an IR Remote Receiver to the Barcographics 808s Battery installation in the RCU Controlling How to control the projector How to use your RCUHardware set up of the projector address Using your RCU How to program an address into the RCU? How to display a projector address?Input selection Port No Projector input Press Digit Button Analog Picture Controls Controlling chained projectors Start UP of the Adjustment Mode Adjustment Mode 0000 Wrong Starting-Up the Random Access Adjustment mode Overview Random Access Adjustment mode From next Internal Cross Hatch Pattern Selecting Setup PatternInternal # Pattern Picture Tuning Random access adjustment mode selection menuColor Balance Clamp Tuning Sync Fast/Slow AdjustmentPeaking Color Select Port 2 Video or S-VideoLine Doubler option Color Select Focusing Geometry Geometry AdjustmentsHorizontal Phase Adjustment Geometry Crt faceplate border Raster Shift AdjustmentProjected raster Raster Shift LEFT-RIGHT E-W Left-Right east-west AdjustmentsLEFT-RIGHT Seagull Correction Seagull correctionLeft Side Correction Left Side Correction TOP-BOTTOM N-S Top-Bottom north-south AdjustmentsTOP-BOTTOM TOP-BOTTOM N-S Horizontal Size Adjustment Exit will return to Geometry Vertical Linearity Adjustment Vertical Size Adjustment Blanking Adjustments Top blanking Right blanking Bottom blanking Convergence Adjustment Convergence Overview flowchart Service mode Starting up the Service modeService Mode Copy a block Copy ModeIdentification Graphics 808s Deleting block by block Delete ModeDeletion of blocks Deletion of all blocks Run time Change passwordChange Language Barcographics 808s Convergence Mid Set to midpositionUndo Midposition Undo Convergence Midposition Dynamic Astigmatism Dynamic Astigmatism spot shape adjustmentDynamic Astigmatism Gamma corrections G2 AdjustCRT run in cycle Projector Warm UP CRT Drive ModeProjector Warm Up Projector Warm UP Fh= 15.6 kHz Fv= 050 Hz MESSAGES, Warnings and Failure Codes003 Input not available Iris commu Nication Error I2C error Addr FH3RWI commu Nication Error Invalid RWI soft Version Options Line Doubler Kit Magik Interface Ceiling Mount kit CM100Orbiting Kit Adapter and communication cables Orbiting option Orbiting Mode Toggle SwitchesOrbiting Master/Slave Toggle Orbiting Speed Toggle only in Master Orbiting Adjustment procedure Stand-Alone projectorOrbiting Alignment Adjustment procedure multiple projector installations Adjustment Blocks memory blocks Adjustment Blocks and SourceSource numbers 90 Adjustment Blocks and Source Numbers Insert Card