Manuals / Bay Technical Associates / Computer Equipment / Network Card

Bay Technical Associates DS Series, DS62-MD4 Gateway Address, Inactivity Timeout, Break Length

Models: DS Series DS62-MD4 DS62

1 53

Download 53 pages 40.46 Kb

Page 29

Gateway Address

DS62-Network, DS62-MD4 Network/Modem Host Module

Select 2) to enter the Subnet Mask followed by <cr>. Failure to enter the address in the decimal form causes the DS to display the following until it is entered correctly. Default Subnet Mask is 0.0.0.0.

Enter Subnet Mask in dotted decimal form :

Gateway Address

The Gateway is the address of a router to connect to other parts of a network. The Gateway address consists of four bytes, each byte ranging from 0 to 255. If your network uses gateways, this parameter must be programmed before the DS can be accessed through the network.

Select 3) to enter the Gateway address. Failure to enter the address in the decimal form causes the DS to display the following until it is entered correctly. Default Gateway address is 0.0.0.0.

Enter Gateway address in dotted decimal form :

Inactivity Timeout

This option enables the DS to disconnect after the programmed amount of time, if there is no activity. Default is 0 (DISABLED). The enabling input can be from 1 to 120 minutes.

Connection Inactivity Timeout is 0 minutes

Enter timeout, in minutes (<=120, 0 to disable) :

Enter 0 to disable or a number between 1 and 120 (inclusive) to set the timeout.

Carriage Return Translation

This option determines what the telnet processor will do with the line-feeds and nulls after a carriage return is sent. Enable tells the DS Telnet processor to strip line feeds or nulls Translation after the carriage returns. Disable allows the characters to pass through. Default is “DISABLED”.

Carriage Return Translation is.... Enabled

Enable ? (Y/N), CR for no change) :

Break Length

Users may configure the DS for a break length of 1 - 1000 milliseconds. In a Telnet session with the DS through the serial port of a DS74, send a Telnet break command (0xF3) to the DS, the serial port will send a break signal of the programmed duration. Default is 350 milliseconds.

Break Length is (msec)	350
Enter break length, in milliseconds (<=10000, 0 to disable) :

29

Image 29

Bay Technical Associates DS Series, DS62 Gateway Address, Inactivity Timeout, Carriage Return Translation, Break Length

Contents

DS Series Manual DATA SWITCH DS62 Host Ethernet ModuleDS62-MD4 Host Ethernet-Modem Module BayTech Manual Publication Revision MayCopyright 2007 by Bay Technical Associates, Inc DS62-Network, DS62-MD4 Network/Modem Host ModuleBayTech, is a registered trademarks of Bay Technical Associates, Inc Tera Term is a product and registered trademark of Vector, Inc10/100 BASE-T NETWORK PORT CONNECTION DS62-Network, DS62-MD4 Network/Modem Host ModuleConnection Description DS Management DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module ABOUT THIS OWNER’S MANUALConnection Description InstallationEIA-232 SERIAL CONNECTION Internal MODEM CONNECTIONPower PREPARING THE INSTALLATION SITEQUICK START HOST Module DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Serial SetupNetwork Port Configuration Login SetupFirmware / Config Download DS62-Network, DS62-MD4 Network/Modem Host ModuleAccess Control Login Setup MenuDS62-Network, DS62-MD4 Network/Modem Host Module Attention Character Manage UsersRadius Configuration Network Port ConfigurationTACACS Configuration DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module CablingRJ-45 Cables and Adapters DS62-Network, DS62-MD4 Network/Modem Host Module Adapters9FRJ45PC With Cisco Interface 9FRJ45PC-1 Without Cisco InterfaceDS62-MD4 Main ScreenDetail Operations and Configurations DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Unit Configuration MenuConfiguration Status DHCP DS62-Network, DS62-MD4 Network/Modem Host ModuleTelnet Handshaking Serial Port ConfigurationDefault is None DS62-Network, DS62-MD4 Network/Modem Host ModuleWord Size Baud RateSelect “Word Size” and the DS displays the following Default is DS62-Network, DS62-MD4 Network/Modem Host ModuleRTS/DTR Line Driver Inactivity State DS62-Network, DS62-MD4 Network/Modem Host Module Stop BitsParity Attention Character Serial Port Device NameDisconnect Timeguard Connect Port ID EchoAccess Control Login Setup MenuManage Users Coldfire login root or Universal DS login root PasswordPasswordADD User Change User’s Port Access and PasswordDS62-Network, DS62-MD4 Network/Modem Host Module Select a non-root user and the DS displays DS62-Network, DS62-MD4 Network/Modem Host ModuleDirect Port Connection Radius ConfigurationDS62-Network, DS62-MD4 Network/Modem Host Module Delete UserDS62-Network, DS62-MD4 Network/Modem Host Module TACACS ConfigurationSetting Up TACACS DS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Network Port ConfigurationSubnet Mask IP AddressDS62-Network, DS62-MD4 Network/Modem Host Module Enter IP address in dotted decimal formGateway Address Inactivity TimeoutCarriage Return Translation Break LengthIP Filter Configuration DS62-Network, DS62-MD4 Network/Modem Host Module DHCP/Telnet/SSHSSH Host Key Generation Select F, Flush Rules to delete all rules. The DS displays DS62-Network, DS62-MD4 Network/Modem Host ModuleSelect D, Delete Rule to delete a specific rule. The DS displays SNMP ConfigurationDS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module SNMP is ENABLED. Enable? Y/NRead/Write Community String Community String Accept changes ? Y/NDefault is Disabled Web Server ConfigurationDefault is Enabled Default is zero minutesModule Name Internal Alarm ThresholdDS Management DS62-Network, DS62-MD4 Network/Modem Host ModuleSelect 1, the DS displays External Alarm ThresholdDS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Outlet GroupsOption 1 and 3 sets the temperature levels to the tenth of a degree. Option 2 and 4 enable the SNMP traps to be sent if the corresponding threshold had been exceeded Select 1, List Outlet Groups to list any outlet groups, the DS display DS62-Network, DS62-MD4 Network/Modem Host ModuleEnable Firmware Upgrade Firmware / Config DownloadEnabling this will allow the firmware to be updated via ftp Enable Firmware Upgrade ? Y/NEnable Configuration File Upload Get Current Configuration File Restore Configuration DefaultsNOTE The network default IP Address, Subnet, and Gateway is DS62-Network, DS62-MD4 Network/Modem Host ModuleModem Port Configuration Display Configuration Error LogDS62-MD4 Modem Configuration Menu DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Modem Inactivity Timeout Modem Connectivity TimeoutRings to Auto Answer Modem Device NameOverall System Status Status MenuNetwork Status DS62-Network, DS62-MD4 Network/Modem Host ModuleMemory Usage Logged UsersCurrent Routing Cache DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Route SetupProcesses Logout Unit ResetUnitInfo Database DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module TroubleshootingFunctional Solutions DS62/DS62-MD4 DS62 and DS62-MD4 Reset procedureDS62-Network, DS62-MD4 Network/Modem Host Module BayTech Extended Warranty BayTech Product WarrantyDS62-Network, DS62-MD4 Network/Modem Host Module Exceptionsfrom the power source before servicing or dismantling Technical SupportDS62-Network, DS62-MD4 Network/Modem Host Module Bay Technical Associates, Inc 5239 A AvenueDS62-Network, DS62-MD4 Network/Modem Host Module Return Authorization ProcessBay Technical Associates 5239 A Avenue Long Beach Industrial Park Long Beach, MS 39560 RA #