Manuals / Bay Technical Associates / Computer Equipment / Network Card

Bay Technical Associates DS Series manual DS62 and DS62-MD4 Reset procedure, DS62/DS62-MD4

Models: DS Series DS62-MD4 DS62

1 53

Download 53 pages 40.46 Kb

Page 50

DS62 and DS62-MD4 Reset procedure

DS62-Network, DS62-MD4 Network/Modem Host Module

e.From your PC create a terminal session to the serial port. Default setting is 9600, 8, 1, no parity, no flow.

f.Type several random characters to see them echoed in the telnet/modem session.

g.Select the telnet/modem session and type several random characters to see them echoed in the PC serial session.

h.This verifies the Chassis, Host module, and the I/O port is working.

i.Move pc cable to next DS74 port and repeat steps (c-h).

If a DS74 module appears not to be working, move the module to a different slot and retest.

DS62 and DS62-MD4 Reset procedure

Figure 1

DS62-MD4 similar to DS62

Caution: This procedure will reset configuration to factory default.

DS62/DS62-MD4:

1.Remove the module from the chassis (with the unit powered down).

2.Hold the module with the chip side up and the faceplate towards you.

3.Locate jumper JMP5 approximate center of circuit board.

4.Move the jumper from pins 1 and 2 to pins 2 and 3.

5.Put the module back in the chassis and power up for 15 seconds.

6.Take the module back out and replace the jumper to the original position. The module is now reset to factory default.

Note: If the module appears not to have reset or opening menu has random characters in it, perform the reset procedure again except increase the reset time from 15 to 30 seconds.

50

Image 50

Bay Technical Associates DS Series DS62 and DS62-MD4 Reset procedure, DS62-Network, DS62-MD4 Network/Modem Host Module

Contents

DS62-MD4 Host Ethernet-Modem Module DATA SWITCH DS62 Host Ethernet ModuleDS Series Manual BayTech Manual Publication Revision MayBayTech, is a registered trademarks of Bay Technical Associates, Inc DS62-Network, DS62-MD4 Network/Modem Host ModuleCopyright 2007 by Bay Technical Associates, Inc Tera Term is a product and registered trademark of Vector, Inc10/100 BASE-T NETWORK PORT CONNECTION DS62-Network, DS62-MD4 Network/Modem Host ModuleConnection Description DS62-Network, DS62-MD4 Network/Modem Host Module DS ManagementABOUT THIS OWNER’S MANUAL DS62-Network, DS62-MD4 Network/Modem Host ModuleEIA-232 SERIAL CONNECTION InstallationConnection Description Internal MODEM CONNECTIONQUICK START HOST Module PREPARING THE INSTALLATION SITEPower DS62-Network, DS62-MD4 Network/Modem Host ModuleSerial Setup DS62-Network, DS62-MD4 Network/Modem Host ModuleFirmware / Config Download Login SetupNetwork Port Configuration DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Attention Character Login Setup MenuAccess Control Manage UsersTACACS Configuration Network Port ConfigurationRadius Configuration DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module CablingRJ-45 Cables and Adapters 9FRJ45PC With Cisco Interface AdaptersDS62-Network, DS62-MD4 Network/Modem Host Module 9FRJ45PC-1 Without Cisco InterfaceDetail Operations and Configurations Main ScreenDS62-MD4 DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Unit Configuration MenuConfiguration Status DHCP DS62-Network, DS62-MD4 Network/Modem Host ModuleTelnet Default is None Serial Port ConfigurationHandshaking DS62-Network, DS62-MD4 Network/Modem Host ModuleSelect “Word Size” and the DS displays the following Default is Baud RateWord Size DS62-Network, DS62-MD4 Network/Modem Host ModuleRTS/DTR Line Driver Inactivity State DS62-Network, DS62-MD4 Network/Modem Host Module Stop BitsParity Disconnect Timeguard Serial Port Device NameAttention Character Connect Port ID EchoManage Users Login Setup MenuAccess Control Coldfire login root or Universal DS login root PasswordPasswordADD User Change User’s Port Access and PasswordDS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Select a non-root user and the DS displaysDS62-Network, DS62-MD4 Network/Modem Host Module Radius ConfigurationDirect Port Connection Delete UserDS62-Network, DS62-MD4 Network/Modem Host Module TACACS ConfigurationSetting Up TACACS DS62-Network, DS62-MD4 Network/Modem Host Module Network Port Configuration DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module IP AddressSubnet Mask Enter IP address in dotted decimal formCarriage Return Translation Inactivity TimeoutGateway Address Break LengthIP Filter Configuration DS62-Network, DS62-MD4 Network/Modem Host Module DHCP/Telnet/SSHSSH Host Key Generation DS62-Network, DS62-MD4 Network/Modem Host Module Select F, Flush Rules to delete all rules. The DS displaysSelect D, Delete Rule to delete a specific rule. The DS displays SNMP ConfigurationDS62-Network, DS62-MD4 Network/Modem Host Module Read/Write Community String Community String SNMP is ENABLED. Enable? Y/NDS62-Network, DS62-MD4 Network/Modem Host Module Accept changes ? Y/NDefault is Enabled Web Server ConfigurationDefault is Disabled Default is zero minutesDS Management Internal Alarm ThresholdModule Name DS62-Network, DS62-MD4 Network/Modem Host ModuleSelect 1, the DS displays External Alarm ThresholdDS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module Outlet GroupsOption 1 and 3 sets the temperature levels to the tenth of a degree. Option 2 and 4 enable the SNMP traps to be sent if the corresponding threshold had been exceeded DS62-Network, DS62-MD4 Network/Modem Host Module Select 1, List Outlet Groups to list any outlet groups, the DS displayEnabling this will allow the firmware to be updated via ftp Firmware / Config DownloadEnable Firmware Upgrade Enable Firmware Upgrade ? Y/NEnable Configuration File Upload NOTE The network default IP Address, Subnet, and Gateway is Restore Configuration DefaultsGet Current Configuration File DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-MD4 Modem Configuration Menu Display Configuration Error LogModem Port Configuration DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Rings to Auto Answer Modem Connectivity TimeoutModem Inactivity Timeout Modem Device NameNetwork Status Status MenuOverall System Status DS62-Network, DS62-MD4 Network/Modem Host ModuleCurrent Routing Cache Logged UsersMemory Usage DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module Route SetupProcesses UnitInfo Database Unit ResetLogout DS62-Network, DS62-MD4 Network/Modem Host ModuleDS62-Network, DS62-MD4 Network/Modem Host Module TroubleshootingFunctional Solutions DS62/DS62-MD4 DS62 and DS62-MD4 Reset procedureDS62-Network, DS62-MD4 Network/Modem Host Module DS62-Network, DS62-MD4 Network/Modem Host Module BayTech Product WarrantyBayTech Extended Warranty ExceptionsDS62-Network, DS62-MD4 Network/Modem Host Module Technical Supportfrom the power source before servicing or dismantling Bay Technical Associates, Inc 5239 A AvenueBay Technical Associates 5239 A Avenue Return Authorization ProcessDS62-Network, DS62-MD4 Network/Modem Host Module Long Beach Industrial Park Long Beach, MS 39560 RA #